Bosch HMD8451UC インストール手順

English 3

This appliance complies with the latest version of one or 

more of the following standards:
•  CAN/CSA C22.2 No. 61 - Household Cooking Ranges
•  UL 858 - Household Electric Ranges
•  CAN/CSA C22.2 No. 150 - Microwave Ovens
•  UL 923 - Microwave Cooking Appliances
•  UL 507 - Electric Fans
•  CAN/CSA C22.2 No. 113 - Fans and Ventilators
•  CSA C22.2 No. 64 - Household Cooking and Liquid-Heating 

Appliances

•  UL 1026 - Electric Household Cooking and Food Serving 

Appliances

It is the responsibility of the owner and the installer to 

determine if additional requirements and/or standards apply 

to specific installations.

This appliance must be grounded. In the event of an elec-

trical short circuit, grounding reduces the risk of electric 

shock by providing an escape wire for the electric current. 

This appliance is equipped with a cord having a grounding 

wire with grounding plug. The plug must be plugged into a 

outlet that is properly installed and grounded.

Improper use of the grounding can result in a risk of 

electric shock.

Consult a qualified electrician or serviceman if the ground-

ing instructions are not completely understood, or if doubt 

exists as to whether the appliance is properly grounded. 
Do not use an extension cord. If the power supply cord is 

too short, have a qualified electrician or serviceman install

an outlet near the appliance. 
The installer must perform a ground continuity check on 

the power outlet box before beginning the installation to 

insure that the outlet box is properly grounded. If not prop-

erly grounded, or if the outlet box does not meet Electrical 

Requirements, a qualified electrician should be employed

to correct any deficiences.

•  For safety considerations, do not install Drawer 

Microwave in any combustible cabinetry which is not 

in accord with the stated clearances and dimensions 

in the "Drawer Microwave Measurements” section 

following. See Figure 3 (standard installation) or Figure 

4 (flush installation).

•  Dimensions that are shown in Figure 3 (standard installa-

tion) or Figure 4 (flush installation) must be used. Given

dimensions provide minimum clearance. Locate electrical 

outlet in the shaded area in the upper left-hand corner of the 

cutout. See Figure 6.

•  Supporting surface must be solid and level. Pay special 

attention to the floor of the cabinet opening on which the

Drawer Microwave will sit. The floor of the opening should

be constructed of plywood strong enough to support the 

weight of the oven (about 100 pounds).

•  Check the location where the Drawer Microwave will be 

installed for proper electrical supply.

•  Your oven can be built into a cabinet or wall as a stand-

alone unit or under a built-in gas or electric wall oven and 

the followings:

NGM5055UC

NGM5655UC

NGM8055UC

NGM8065UC

NGM8655UC

NGM8665UC

NGMP055UC

NGMP655UC

NEM5066UC

NET8066UC

NET8066SUC

NETP066SUC

NEM5666UC

NET8666UC

NET8666SUC

NETP666SUC

NIT5066UC

NIT8066UC

NIT8066SUC

NITP066UC

NITP066SUC

NIT5666UC

NIT8666UC

NIT8666SUC

NITP666UC

NITP666SUC

•  Check to be sure that there is a clearance of 2 inches or 

greater between the top of the Drawer Microwave unit and 

the bottom of a built-in wall oven above it.

•  The microwave interior will easily accommodate a 9" x 13" 

oblong dish or a bag of microwave popcorn.