Smeg CMSU6451X ユーザーズマニュアル

14

The coffee mill is preset in the factory to make coffee correctly 
and should not require adjusting initially.
However, if after making the first few coffees you find that de-
livery is either too fast or too slow (a drop at a time), this can be 
corrected by adjusting the grinding adjustment knob (fig. 12). 
Turn one click clockwise (one number) for more rapid coffee de-
livery (not a drop at a time). 
Turn one click anticlockwise for slower coffee delivery and a 
creamier coffee. These adjustments will only be evident after at 
least 2 cups of coffee have been delivered.
The grinding adjustment knob must only be turned when the 
coffee mill is in operation.

For slower delivery and creamier coffee, turn one click anticlock-
wise (finer pre-ground coffee).
For faster delivery (not a drop at a time), turn one click clockwise 
(coarser pre-ground coffee).
(Coffee has been used to factory test the appliance and it is 
therefore completely normal for there to be traces of coffee in 
the mill. It is, however, guaranteed to be new.)

•  Press the  

 button (C3) (fig. 16) to select the pre-

ground coffee function. This disables the coffee mill func-
tion.

 

The appliance now displays the message: “READY PRE-
GROUND”.

•  Extract the machine by pulling it outwards using the han-

dles. 

•  Lift the central lid, place one measure of pre-ground coffee 

in the funnel (fig. 17), push the appliance in then proceed 
as  described  in  the  section “Making  coffee  using  coffee 
beans”.

 

N.B.: You can make just one coffee at a time by pressing the 

 (C8), 

  (C9) or 

(C10) button once only.

•  After using the machine with pre-ground coffee, to go back 

to making coffee using beans, deactivate the pre-ground 
coffee function by pressing the 

 button (C7) again to 

enable the coffee mill.

NOTE 1: Never introduce pre-ground coffee when the machine is 
off or it could spread through the inside of the appliance. 
NOTE 2: Never add more than 1 level measure, otherwise either 
the appliance will not make the coffee and the pre-ground 
coffee will be dispersed inside the appliance, dirtying it, or the 
coffee will be delivered a drop at a time.
NOTE 3: Use the measure provided to add the right amount of 
coffee. 
NOTE 4: Introduce only pre-ground coffee for espresso coffee 
machines into the funnel. Never fill with coffee beans, freeze 
dried coffee or other substance that could damage the appli-
ance.
NOTE 5: If more than one measure of pre-ground coffee is used 
and the funnel clogs, push the coffee down with a knife (fig. 18) 
then remove and clean the infuser and machine as described in 
the “Cleaning the infuser” section. 

•  Always make sure the appliance is ready.
•  Make sure the hot water spout is in place (fig. 4);
•  Position a container under the spout (fig. 3).
•  Press the 

  button (C5) (fig. 1).

 

The message “HOT WATER” is displayed and hot water flows 
out of the hot water spout into the container.  

 

(You should not deliver hot water for more than 2 minutes 
at a time). 

 

To interrupt the flow, press the 

   button (C5).

 

Once the set quantity of hot water has been reached, deliv-
ery stops automatically. 

The appliance is set by default to automatically deliver about 
200 ml / 6.76 oz of hot water. 
To change these quantities, proceed as follows:
•  Attach the hot water spout (fig. 4).
•  Position a container under the spout (fig. 3).
•  Hold the 

 button (C5) down for at least 2 seconds then 

release it. The message “HOT WATER PROGRAM QUANTITY” 
is displayed and hot water flows out of the hot water spout. 

•  When the hot water in the cup reaches the required level, 

press the 

  button (C5) to memorise the new amount. 

 

(You should not deliver hot water for more than 2 minutes 
at a time).

•  Select the taste of the coffee you want to use to make the 

cappuccino by pressing the 

  button (C7).