Electrolux EW30ES80RS オーナーマニュアル
![Electrolux](https://files.manualsbrain.com/attachments/3404bb22dccbcfb6fc3ca6ee6cf2547381b94656/common/fit/150/50/424ff1215290c4147facb2112ed5c71f65e2af857b7bc4f69bdf4447be5b/brand_logo.png)
53
Solutions to common problems
Before you call for service, review the following list. It may save you time & expense. The list includes
common occurrences that are not the result of defective workmanship or materials in this appliance.
Questions or for service call: 1-877-4ELECTR
OLUX
(1-877-435-3287)
Before you call
Problem
Solution
Oven control
beeps and
displays an F
error code.
• Electronic control has detected a fault condition. Push
CANCEL pad to clear
the display and stop the display from beeping. Reprogram the oven. If a fault
reoccurs, record the fault number, push the
CANCEL pad and contact an
authorized servicer.
Installation
• Place oven rack in center of oven. Place a level on the oven rack. Contact
installing agent if rack and cabinet cutout flooring are not level.
• Kitchen cabinet misalignment may make range appear to be not level. Be sure
cabinets are square and level. Contact cabinet maker to correct problem.
Entire range does
not operate
• When the range is first plugged in, or when the power supply to the oven has been
interrupted, the display will flash. The range cannot be programmed until the clock is set.
• Be sure electrical cord is securely connected into the electrical junction box.
• Cord/plug is not installed and/or connected. Cord is not supplied with range.
Contact your dealer, installing agent or authorized servicer.
• Service wiring not complete. Contact your dealer, installing agent or authorized
servicer.
• Power outage. Check house lights to be sure. Call your local electric company.
• Short in cord/plug. Replace cord/plug.
• Controls are not set properly. See instructions to set the controls.
• House fuse has blown or circuit breaker has tripped immediately following
installation.
• House fuse may not be fully engaged. Check fuse and screw or engage circuit
breaker securely.
Oven light does
not work
• Burned out or loose bulb. Check bulb fit in socket. Follow instructions under
“Oven Light” to replace the bulb.
Self-cleaning
cycle does not
work
• Make sure the oven door is closed.
• Make sure you have removed the oven racks and the oven rack supports from
the oven.
• Controls not set properly. Follow instructions under “Setting Self-Clean”.
Poor cooking
results
• Many factors affect baking results. See baking for hints, cause and corrections.
See Adjusting Oven Temperature.
• Adjust the recipe’s recommended power levels or cooking times.
• Cookware is too lightweight or warped. Use heavier quality cookware so foods
being prepared may cook more evenly.
Oven racks do
not slide easily.
• This oven comes with lubricated porcelain oven racks, which can remain in the
oven during the self-clean cycle. Do not clean this vegetable oil lubrication off
the racks. It is important that the sides of the oven racks always have a light
coating of vegetable oil. To maintain optimal rack performance, re-apply a thin
layer of vegetable oil to the sides of the rack after every self-clean cycle or
when the rack becomes difficult to slide.
Glide racks do not
slide smoothly
• Glide racks need lubrication. For instructions on how to care for your oven
racks, see “Caring for Your Porcelain Enameled Glide Racks” on page 51.
Flames inside
oven or smoking
from oven vent
• Excessive spillovers in oven. For example this will happen for pie spillovers or
large amounts of grease left on the oven bottom. Wipe up excessive spillovers
before starting oven. If flames or excessive smoke are present see “About
broiling” in the
Setting Oven Controls section.