Manualsbrain.com
  1. マニュアル
  2. ブランド
  3. Mitsubishi Electronics
  4. XD8600
  5. ユーザーズマニュアル

Mitsubishi Electronics XD8600 ユーザーズマニュアル

ダウンロード
ページ / 79
EN-56
•  Immediately after the power-on, during the lamp
selection, or during the lamp relay operation, you 
cannot change the setting of LAMP SELECT and 
LAMP RELAY. 
•  In the case of continuous projection, the lamps may
deteriorate earlier unless they are turned off for 1 
hour per week. 
•  When using this projector continuously for a long
time of period, enable LAMP RELAY.
•  The brightness and color tint vary at the time of
lamp switching.
When LAMP SELECT is set to SINGLE:
The lamps are automatically switched and used alternately.
(See page 31 for menu setting.)  
1.  Display the INSTALLATION 1 menu.
2.  Select LAMP SELECT by pressing the  or  button.
1 2
LAMP SELECT
DUAL
3.  Press the ENTER button.
4.  Select SINGLE   by pressing the  or  button.
LAMP SELECT
1 2
LAMP SELECT
SINGLE
5.  Press the ENTER button.
6.  Select LAMP RELAY by pressing the  or  button.
LAMP RELAY
24H
7.  Select 24H 
 
or 1 WEEK 
 
by pressing the  or  
button.
24H   .........  The lamps are switched to each other 
every day. 
Off
Illuminating
LAMP 1
LAMP 2
1
2
3
4
5
6
7
8 (days)
At the time of power-on or menu setting
1 WEEK   ..  The lamps are switched to each other 
every week.
LAMP 1
Illuminating
LAMP 2
1
2
3
4
5
6
7
8 (days)
Off
At the time of power-on or menu setting
8.  Press the ENTER button.
•  When you select 24H   or 1 WEEK  , the box 
to set the lamp relay interval is displayed.  
24H 
NEXT LAMP RELAY
24H
0
OK
CLEAR
DEL
CANCEL
1
2
3
4
5
6
7
8
9
←
→
Lamp relay (continued)
1 WEEK 
NEXT LAMP RELAY
7D 00H
0
OK
CLEAR
DEL
CANCEL
1
2
3
4
5
6
7
8
9
←
→
9.  Move the key cursor using the direction buttons to 
select the number you want to enter and then press 
the ENTER button.
•  Maximum interval
  24H   ........... 24H (24 hours)
  1 WEEK   .... 7D 00H (7 days and 00 hours)
 ← key: 
 Shifting the position of enter cursor 
to the left for each character.
 → key: 
 Shifting the position of enter cursor 
to the right for each character.
  DEL key: 
 Deleting the character in the 
position of enter cursor for each 
character.
  CLEAR 
key:  Deleting all the entered characters.
•  You can enter the value by pressing the number
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
•  When the value you entered meets the following
conditions, an error dialog box is displayed at 
the screen center. 
  ∙   The value has been cleared by DEL or CLEAR 
and left blank. 
  ∙   The value you entered is out of the setting 
range.
   
24H    ......... 25H or over
   
1 WEEK    ... 7D 01H or over
  ∙   The value of each item is out of the setting 
range.
   
D .................. 8 or over (1 WEEK   only)
   
H .................. 25 or over
10. When selecting OK, the setting is completed as 
the lamp-switching interval stored. However, when 
selecting CANCEL, the setting is completed without 
storing.
•  The display returns the LAMP RELAY menu after
selecting OK or CANCEL.
•  The setting you made is applied to NEXT LAMP
RELAY in the INFORMATION menu.
Important:
•  When you use the projector continuously, the lamp
relay may not be performed on time due to errors of 
the clock function. 
•  Immediately after the power-on, during the lamp
selection, or during the lamp relay operation, you 
cannot change the setting of LAMP SELECT and 
LAMP RELAY. 
•  In the case of continuous projection, the lamps may
deteriorate earlier unless they are turned off for 1 
hour per week. 
•  When using this projector continuously for a long
time of period, enable LAMP RELAY.
•  The brightness and color tint vary at the time of
lamp switching.