Liebherr 110309 7084282 - 01 ユーザーズマニュアル

Fig. 24 

u

To  align  the  unit  door  in  depth  Z:  Undo  top  screws

Fig. 24 (36)

, bottom hexagon head screws

 Fig. 24 (35)

 with

ring spanner

 Fig. 24 (37)

 provided, then shift the door.

u

Do not allow the knobs and sealing lips to

abut - vital for proper function!

u

Allow an air gap of 2 mm between the unit

door and the body of the unit.

u

fit  a  3rd  pair  of  mounting  brackets

Fig. 11 (34)

.

u

Use the holes pre-drilled in the handle area of

the appliance door for this purpose.

u

Check the fit of

the  door  and

adjust  if  nec-

essary.

u

Tighten 

all

screws.

Fig. 25 

u

Tighten  the  locknuts

  Fig.  25  (32)

  using  the  ring  spanner

Fig.  25  (37)

,  while  holding  fast  the  adjusting  bolts

Fig. 25 (33)

 with a screwdriver.

u

Put on and engage the up-

per covers

 Fig. 26 (38)

.

u

Place 

lateral 

covers

Fig.  26  (39)

  in  position,

slide them to the limit, then

press, until you hear them

snap into place.

u

Attach covers

 Fig. 26 (40)

sideways  and  then  draw

them  forwards  with  a

screwdriver  so  that  they

snap into place.

Fig. 26 

u

Put on and engage the covers

 Fig. 8 (5,6,7)

.

Check the following points to ensure the appliance is fitted prop-

erly. Failure to do so may lead to icing, condensate forming and

malfunction:
w

The door has to close properly

w

The unit door must not butt against the unit body

w

The seal must have a firm fit at the upper corner on the handle

side. To check, darken the room, place a torch inside the ap-

pliance at the top and close the door. If light shines through,

check the assembly.

Risk of injury and danger of damage as a result of incorrect trans-

port!

u

Transport the appliance in a packed condition.

u

Transport the appliance upright.

u

Do not transport the appliance without assistance.

In the event that the appliance is damaged, contact the supplier

immediately before connecting to the mains.
The floor at the site must be flat and level.
Do not install the appliance in a location where it is exposed to

direct radiation of the sun, next to a cooker, heater and similar.
Do not install the appliance without assistance.
Standard EN 378 specifies that the room in which you install your

appliance must have a volume of 1 m

2

 per 8 g of R 600a refrig-

erant used in the appliance. If the room in which the appliance is

installed is too small, a flammable gas-air mixture may form in the

event of a leakage in the refrigeration circuit. The quantity of re-

frigerant used in your appliance is indicated on the type plate on

the inside of the appliance.
Fit the appliance in stable kitchen units only.

The following ventilation gaps must be observed:

q

The depth of the ventilation channel at the rear of the unit must

be at least 38 mm.

q

There must be a ventilation space of at least 200 cm

2

 in the

plinth and at the top of the unit.

q

Basically the principle applies: the larger the ventilation space,

the more energy-saving the appliance is in operation.

Fire hazard due to dampness!

If live parts or the mains lead become damp this may cause short

circuits.

u

The appliance is designed for use in enclosed areas. Do not

operate the appliance outdoors or in areas where it is exposed

to splash water or damp conditions.

Fire hazard due to refrigerant!

The refrigerant R 600a is environmentally friendly but flammable.

Escaping refrigerant may ignite.

u

Do not damage the piping of the refrigeration circuit.

Fire hazard and danger of damage!

u

Do not place appliances emitting heat e.g. microwaves, toast-

ers etc. on the appliance!