Extron electronic MGP 464W ユーザーズマニュアル

ページ / 4
The MGP Series are multi-window video signal processors that can display 
multiple video sources on a single screen in picture-in-picture or picture-by-
picture format.  The processors can switch among inputs as well as picture 
controls and presets.  The available models are listed below.  The MGP 464 
models display up to four windows; the MGP 462xi models display one or two.
MGP 464/MGP 462xi
 — Standard models with BNC input connectors that accept RGB, component video, 
S-video, or composite video 
MGP 464 DI/MGP 462xi DI
 — An MGP 464/462xi with a DVI input card installed, providing four DVI input 
connectors.  
MGP 464 HD-SDI/MGP 462xi HD-SDI
 — An MGP 464/462xi with two HD-SDI inputs and two DVI inputs.  
MGP 464W/MGP 464W DI
 — Designed for WindoWall
 video wall systems and available in sets of two or 
three processors.  These models have no front panel controls and are controllable only via software.  Each MGP 
displays up to four windows.  
This guide provides procedures for installing all 
MGP 464 and MGP 462xi models, and for configuring all 
models except the MGP 464W series.  To configure the 
MGP 464W models (done via software only), refer to the 
WindoWall Console help file or the WindoWall Console 
Quick Reference 
card.
Installation
1
Install the four rubber feet on the bottom of the 
MGP, or mount the unit using the supplied rack 
mounting brackets.    
2
Turn off power to the input and output devices, and 
remove the power cords from them.
3
Connect the input sources to the MGP's BNC, DVI, 
and/or HD-SDI input connectors.  The inputs can 
accept the following signal types:
 
RGB/HD/video inputs 1, 2, 3, and 4 
— RGB, component video, S-video, or composite video (fully configurable)
  
RGBHV
Video
RGsB or
Component
Video
S-Video
Composite
Video
RGBS or
RGBcvS
Video
H
/HV
V
R
/R-Y
G
/Y
VID
B
/C
B-Y
H/HV
B/C
B-Y
H
/HV
V
R
/R-Y
G
/Y
VID
B
/C
B-Y
V
R/R-Y
G/Y
VID
B
/C
B-Y
H/HV
V
R/R-Y
G/
Y
VID
B
/C
B-Y
H/HV
V
R/R-Y
G/Y
VID
1
1
1
1
1
DVI inputs 1, 2, 3, and 4
 — These inputs can be used instead of, or in combination with, 
analog inputs 1 through 4.  (However, the MGP cannot process input from two 
different source devices connected to DVI and BNC connectors with the same input 
number — for example, input 1— at the same time).  The DVI inputs are available 
only on the MGP 464/462xi DI and HD-SDI models.  
N
  Analog is not available on these DVI-I connectors.  
HD-SDI inputs 1 and 2
 — These inputs can be used instead of, or in combination with, 
analog inputs 1 and 2.  The HD-SDI inputs are only on the MGP 464/462xi HD-SDI.  
N
  Standard definition SDI is not supported on these HD-SDI inputs.
68-1666-01 Rev. B
06 09
INPUT  1-DVI-D
INPUT  1-HD-SDI
MGP Series Setup Guide 
Rack mounting the MGP
MBD 249
2U Rack Mounting
Bracket (Use four
lower holes.)