Canon IP2000 ユーザーズマニュアル
Troubleshooting
71
Cannot Print Properly from the Digital Camera
The following are the possible errors that may occur when printing directly from a digital still
camera or digital video camcorder*, and the countermeasures to eliminate them.
camera or digital video camcorder*, and the countermeasures to eliminate them.
* Hereafter, the digital still camera and digital video camcorder are collectively called a digital camera or camera.
*
1
To resume printing, you can press the R
RESUME/CANCEL button on the printer instead of selecting C
Continue.
*
2
The waste ink absorber absorbs ink used during cleaning.
Camera Error Message
Possible Cause
Try This
Printer in use
Images are being printed from
the computer
the computer
Wait until printing ends. The printer automatically starts
printing the images from the camera after completing the
current printing.
printing the images from the camera after completing the
current printing.
Printer warming up
The printer is warming up
Wait until warm-up ends. When it is ready, the printer starts
printing automatically.
printing automatically.
No paper
No paper is loaded
Load the paper in the Auto Sheet Feeder of the printer and
select C
select C
Continue*
1
in the display on your camera. The Front
Sheet Feeder cannot be used for printing.
Paper error
The Paper Output Tray is
closed
closed
Open it. Printing will resume.
Paper Jam
A paper jam occurrs in the
printer
printer
Select C
Cancel in the display on your camera to cancel the print
job. Remove the jammed paper, load new media, and press the
RESUME/C
RESUME/C
CANCEL button.
Printer cover open
The Front Cover is open
Close the Front Cover.
No Print Head
No Print Head is installed (The
POWER lamp on the printer
flashes five times)
POWER lamp on the printer
flashes five times)
Install a Print Head according to the
Easy Setup Instructions.
If a Print Head has already been installed, remove it, check that
its contacts are clean, and then reinstall it.
If the problem still remains, the Print Head may be defective.
Contact the Customer Care Center.
its contacts are clean, and then reinstall it.
If the problem still remains, the Print Head may be defective.
Contact the Customer Care Center.
The Print Head is defective
(The P
(The P
POWER lamp on the
printer flashes five times)
Waste tank (Waste ink
absorber*
absorber*
2
) full
The waste ink absorber*
2
is
nearly full
The printer has a built-in waste ink absorber to hold the ink
used during Print Head cleaning. This error message indicates
that the waste ink absorber is nearly full.
Selecting C
used during Print Head cleaning. This error message indicates
that the waste ink absorber is nearly full.
Selecting C
Continue*
1
in the display on your camera resumes
printing. Printing can be continued for a while, but printing
cannot be continued when the waste ink absorber becomes full.
Contact the Customer Care Center as soon as possible.
cannot be continued when the waste ink absorber becomes full.
Contact the Customer Care Center as soon as possible.
Ink is low
It is about time to replace the
ink tank with a new one
ink tank with a new one
Select C
Continue*
1
in the display on your camera to resume
printing.
Ink tank is empty
Replace the ink tank with a
new one
new one
Printing resumes once the Front Cover is closed after ink tank
replacement.
You can continue printing by selecting C
replacement.
You can continue printing by selecting C
Continue*
1
in the display
on your camera with the ink tank empty. But, it is recommended
you replace it with a new one immediately after printing. It may
damage the printer if you continue printing with empty ink
tanks.
you replace it with a new one immediately after printing. It may
damage the printer if you continue printing with empty ink
tanks.
Printer error
An error requiring servicing
might have occurred (The
POWER lamp on the printer
flashes alternately orange and
green)
might have occurred (The
POWER lamp on the printer
flashes alternately orange and
green)
Select C
Cancel in the display on your camera to cancel the print
job.
Disconnect the cable connected to the camera, turn off the
printer, and unplug the power cord of the printer from the
outlet. Leave the printer for a while, plug the power cord of the
printer back in the outlet, turn on the printer, and connect the
camera to the printer.
If the error persists, contact the Customer Care Center.
Disconnect the cable connected to the camera, turn off the
printer, and unplug the power cord of the printer from the
outlet. Leave the printer for a while, plug the power cord of the
printer back in the outlet, turn on the printer, and connect the
camera to the printer.
If the error persists, contact the Customer Care Center.
QSG_Shoot.fm Page 71 Wednesday, May 19, 2004 5:37 PM