Shark S3250W 11 ユーザーズマニュアル
10
TOLL FREE:
1-800-798-7398
11
www.sharkclean.com
English
CARE OF YOUR MICRO-FIBER
CLEANING PAD
1
Wash pads in warm water. Wash
separately from other laundry. Only
use liquid detergent (no powder
detergent). Do not use fabric
softeners. Line dry or dry on a low
dryer setting. (
use liquid detergent (no powder
detergent). Do not use fabric
softeners. Line dry or dry on a low
dryer setting. (
fig. 5)
2
If there are loose threads on the
pad carefully cut the threads with
scissors. Do not pull on them or cut
at the base. (
scissors. Do not pull on them or cut
at the base. (
fig. 6)
IMPORTANT: The micro-fiber
cleaning pad may be very hot
from the steam. Use caution when
removing. Let the unit cool for 2-3
minutes.
cleaning pad may be very hot
from the steam. Use caution when
removing. Let the unit cool for 2-3
minutes.
Care of Your Light & Easy™ Steam Mop
ORDERING REPLACEMENT PARTS
To order additional parts and
accessories, feel free to contact us at
www.sharkclean.com or call
1-800-798-7398.
To order additional parts and
accessories, feel free to contact us at
www.sharkclean.com or call
1-800-798-7398.
NOTE: Some parts may be available
at your local retailer. Contact customer
service for any other servicing.
at your local retailer. Contact customer
service for any other servicing.
fig. 5
fig. 6
Trouble Shooting
PROBLEM
POSSIBLE REASONS & SOLUTIONS
The Light & Easy™
Steam Mop will not
turn-on.
Your steam-mop should be securely plugged into a
120V AC electrical outlet only.
120V AC electrical outlet only.
Check your fuse or breaker.
If your unit still does not work, call
1-800-798-7398.
Light & Easy™
Steam Mop will not
make steam.
Is there water in the water tank? If not, add water to your
Steam Mop following instructions on page 5.
Steam Mop following instructions on page 5.
Light & Easy™
Steam Mop leaves
water on the floor.
Is your micro-fiber cleaning pad too wet? Unplug your
Steam Mop and change the micro-fiber cleaning pad.
Steam Mop and change the micro-fiber cleaning pad.
Light & Easy™
Steam Mop left
white spot on the
floor.
Do not leave your steam-mop on the floor with a damp or
wet cleaning pad.
wet cleaning pad.
Do you have hard water? If you do, you might want to
switch to distilled water.
switch to distilled water.
Make sure the water is securely on the water tank.
Floors are cloudy,
streaky or spotty
after steaming.
The pad might be dirty, change the pad.
If you washed the pocket with powder detergent, then the
pad may have residual detergent left on it. Wash it again
with liquid detergent.
pad may have residual detergent left on it. Wash it again
with liquid detergent.
If you are cleaning in a kitchen area where there might be a
build-up of grease, use a de-greasing agent such as an all-
purpose cleaner or dish soap and paper towels to clean the
area first.
build-up of grease, use a de-greasing agent such as an all-
purpose cleaner or dish soap and paper towels to clean the
area first.
You might have left the mop in the same spot for too long.
Do you have hard water? If you do, you might want to
switch to distilled water.
switch to distilled water.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if
the leftover cloudiness is removed.
surface. Use the steam mop a few more times and see if
the leftover cloudiness is removed.
Light & Easy™
Steam Mop is hard
to push.
Make sure the steam pad is attached correctly.
Check to see if the cleaning pad is excessively dirty.
Replace if the pad is too dirty or wet.
Check to see if the cleaning pad is excessively dirty.
Replace if the pad is too dirty or wet.
S3250W_11_IB_ENG_100505.indd 10-11
10-05-05 4:14 PM