Tascam CC-222MKIV ユーザーズマニュアル
1 – Introduction
16
TASCAM CC-222
MK
IV
4 – Disc operations
Time display modes
When playing back a CD, or when in standby mode, there
are four different time display modes.
In each mode, the current track number is given, fol-lowed
In each mode, the current track number is given, fol-lowed
by the time, as given below, e.g.
10Tr 0:48
Press the
DISPLAY
key to cycle through these time display
modes, as described here:
Display shows
Display shows
Meaning
TOTAL
Total elapsed time of the disc
TOTAL REMAIN
Time remaining of the current disc
[blank]
Elapsed time of the current track
REMAIN
Time remaining of the current track
NOTE
If the Program playback has been selected (see
”Program playback” on page 17), the elapsed time and
total remaining time refer to the programmed material,
not the whole disc.
”Program playback” on page 17), the elapsed time and
total remaining time refer to the programmed material,
not the whole disc.
Track search
Use the
MULTI DIAL
(or the
SKIP
keys on the remote
control unit) to jump forward or backward by one track at a
time, as shown on the display.
Note that going forward from the last track of the disc will
Note that going forward from the last track of the disc will
“wrap round” to track 1, and going backward from the first
track of the disc will “wrap round” to the last track of the disc.
It is also possible to use the number keys on the remote
It is also possible to use the number keys on the remote
control unit to jump directly to a particular track:
1 To play tracks 1 through 9, simply press the appro-
1 To play tracks 1 through 9, simply press the appro-
priate key (1 through 9).
2 To play a track whose number is higher than 9,
press the +10 key an appropriate number of times to
set the “tens” digit of the track number, followed by
a single key to set the “units” digit. For example:
Track 13 = +10, 3
Track 30 = +10, +10, +10, 0
NOTE
On the remote control unit only, the search keys can be
used to ”fast-forward” and ”fast-rewind” through the disc.
used to ”fast-forward” and ”fast-rewind” through the disc.
Simple playback operations
WARNING
If you are monitoring using headphones, first adjust
the level control to low on the unit, then connect to the
PHONES jack before playing back. This will prevent
any possible damage to your hearing.
the level control to low on the unit, then connect to the
PHONES jack before playing back. This will prevent
any possible damage to your hearing.
1 Press
OPEN/CLOSE
key to open the disc tray.
2 Discs should be inserted in the tray with the label up-
permost.
3 Press the
OPEN/CLOSE
key to close tray.
When a disc is loaded into the unit, the display briefly
shows
TOC Reading.
, with a flashing period as the unit
determines the contents of the disc. When the TOC has
been read, the display shows (at the left of the display) one
of the following:
CD
CD
Commercial pre-recorded CD
CD-R/CD-RW
Finalized CD-R or CD-RW
CD-R, NO TOC
CD-R which has yet to be finalized
CD-RW, NO TOC CD-RW which has yet to be finalized
4 Press the
PLAY
key to start playback
The track number indicators at the bottom of the display
light, to show the available tracks playing back. If there are
thirteen tracks on the disc, for example, indicators 1 through
13 will light. If there are more than 20 tracks on the disc,
“
OVER
” will light at the end of the track number indicators.
Pressing the
STOP
key stops playback.
Pressing the
PAUSE
key pauses playback temporarily.
To resume playback, press the
PAUSE
key again or the
PLAY
key.