Magnavox MDR535H ユーザーズマニュアル
33
EN
EN
Connections
Basic Setup
Recording
Playback
Editing
Introduction
Function Setup
Others
Español
Connections
Basic Setu
p
Basic Setup
Recording
Playback
Editing
Introduction
Function Setup
Others
Español
SETTING THE CLOCK
Note for auto clock setting
• The clock may set itself automatically after this unit
receives the antenna/cable signal and plug in the
power cord.
power cord.
• If the clock is not set correctly, timer recording does
not work properly.
• Analog off the air broadcasts have ended. Analog
auto clock setting will no longer be available except
via Cable TV. Try digital auto clock setting in this
case.
via Cable TV. Try digital auto clock setting in this
case.
• For Digital auto clock setting, incorrect time may be
obtained depending on the broadcast information.
If this occurs, set the “Auto Clock Setting“ to “OFF” at
step 4 and try “Manual Clock Setting“ on page 34.
If this occurs, set the “Auto Clock Setting“ to “OFF” at
step 4 and try “Manual Clock Setting“ on page 34.
Manual Auto Clock Setting
If the unit chooses an incorrect PBS channel on Cable
TV, set the PBS channel manually by following the steps
below.
TV, set the PBS channel manually by following the steps
below.
1
Select “Manual” at step 4 in “Analog
Auto Clock Setting” on page 32, then
press [OK].
press [OK].
2
Use [the Number buttons] or [
K/ L]
to enter your Cable TV Analog PBS
channel number, then press [OK].
channel number, then press [OK].
Set Channel No.
CH 1
3
Press [MENU] to exit and turn the
unit to the standby mode.
Digital Auto Clock Setting
1
Press [MENU] and use [
K / L] to select
“General Setting”, then press [OK].
“General Setting” menu will appear.
2
Use [
K/ L] to select “Clock”, then
press [OK].
“Clock” menu will appear.
3
Use [
K/ L] to select “Auto Clock
Setting”, then press [OK].
4
Use [
K/ L] to select “Manual”, then
press [OK].
Auto Clock Setting
OFF
Auto
Manual
Auto
Manual
Enable Manual operation to select the DTV
Channel for receiving the Clock Data and
selecting your Time Zone below.
Channel for receiving the Clock Data and
selecting your Time Zone below.
5
Press [
{ ] to highlight “CH”. Press
{
[
K / L] to select “DTV”, then press
[
B] .
Set Channel No.
DTV 1
6
Use [the Number buttons] or [
K/ L]
to enter the desired major channel
number to receive the Clock Data,
then press [OK].
number to receive the Clock Data,
then press [OK].
Time adjustment for each time zone
Atlantic
GMT (Greenwich Mean Time ) - 4 hours
Eastern
GMT (Greenwich Mean Time ) - 5 hours
Central
GMT (Greenwich Mean Time ) - 6 hours
Mountain
GMT (Greenwich Mean Time ) - 7 hours
Pacific
GMT (Greenwich Mean Time ) - 8 hours
Alaska
GMT (Greenwich Mean Time ) - 9 hours
Hawaii
GMT (Greenwich Mean Time ) - 10 hours
7
Use [
K /L] to select the desired time
zone, then press [OK].
Time Zone
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
8
Press [MENU] to exit and turn the
unit to the standby mode.
unit to the standby mode.
This unit will search for the time only when the
power is in the standby mode. Initially leave it in
standby mode for at least 15 minutes to give this
unit time to set the clock. Once the clock is set, the
unit receives the clock data at 12:00 am & 12:00 pm
when unit is in standby mode. Check the time after
the Auto Clock was set, if it is incorrect time then set
the “Auto Clock Setting“ to “OFF” in step 4 above.
Then try “Manual Clock Setting“ on page 34.
power is in the standby mode. Initially leave it in
standby mode for at least 15 minutes to give this
unit time to set the clock. Once the clock is set, the
unit receives the clock data at 12:00 am & 12:00 pm
when unit is in standby mode. Check the time after
the Auto Clock was set, if it is incorrect time then set
the “Auto Clock Setting“ to “OFF” in step 4 above.
Then try “Manual Clock Setting“ on page 34.
E2S05_07_08UD_UH_MDR533_535_537H_EN_v2.indd 33
2013/02/12 21:06:17