ユーザーズマニュアル目次Introduction1About This Volume11.1.1 Contents11.1.2 Terminology1About the TIA/EIA-136 EAC-210011.2.1 Use of Boosters11.2.2 Frequency Allocation11.2.3 EAC-2100 Operation1Preliminary Decisions2Introduction2Use of Multi-hop Configuration or Multi-donor Units2Site Requirements22.3.1 Location22.3.2 AC Service22.3.3 Space22.3.4 Mounting Surface2Antennas22.4.1 Type22.4.2 Placement22.4.3 Measuring Signal Level and Isolation2Selecting Channels22.5.1 Identifying the Donor DCCH Channel22.5.2 Selecting a Boosted DCCH Channel22.5.3 The Revertive DCCH Channel Option22.5.4 The Substitute DCCH Channel2• Disabling the Substitute DCCH Channel2• Enabling the Substitute DCCH Channel22.5.5 Selecting the Directed Retry Channels22.5.6 Selecting Donor DTC Channels22.5.7 Selecting Boosted DTC Channels2Installing the Hardware3Introduction3Mechanical Installation33.2.1 Uncrating the Equipment33.2.2 Mounting the Cabinet33.2.3 Securing the Doors3Connecting the EAC-2100 to ac Power3Installing the Antennas33.4.1 Connecting the Antennas3Connecting External Alarms/Controls (Optional)3Setting Up for Initial Operation4Introduction4Powering Up the EAC-21004Powering Down the EAC-21004Connecting a Local Terminal4Becoming Familiar with System Commands44.5.1 Basic Commands44.5.2 Using the SET Menus4Setting Initial Parameters44.6.1 Checking System Status44.6.2 Entering the Site ID44.6.3 Setting the Donor DCCH Channel44.6.4 Setting the Boosted DCCH Channel44.6.5 Setting the Directed Retry Channels44.6.6 Setting the Donor DTC Channels44.6.7 Setting the Boosted DTC Channels44.6.8 Programming Alarms and Thresholds4Mobile Power Step, and Passwords4Tuning Transmitter Combiner and Setting Output Power4Power Levels for PAs 1− 5 and 7− 1144.7.2 Adjusting the PA 6 Power Level44.7.3 Setting Reverse Path Output Power (If Necessary)44.7.4 Setting PA Power Low Alarm Points44.7.5 Setting Time and Report Values4Installing the Remote Link5Introduction5Setting Up Service5Programming the Mobile Radio5Checking Out the Mobile5Testing the Remote Link55.5.1 EAC-2100 Answering55.5.2 EAC-2100 Originating5Optimizing Performance6Introduction6Determining Hand-in and Hand-back Thresholds6Setting Hand-in and Hand-back Thresholds6Important Terms Used in This Manual1System Operation1Pre-Installation Checklist2Recommended Space2Typical Antenna Installation2Antenna Isolation v. Horizontal Separation2Antenna Isolation v. Vertical Separation2Hardware Installation Checklist3EAC-2100, Front View (Door Removed)3EAC-2100, Back View (Door Removed)3Outdoor Cabinet Footprint3Antenna Connectors3External Alarm/Control Connector Pin Out3Electrical Specifications for Inputs and Outputs3Typical Wiring for External Inputs and Outputs3Setup Checklist4EAC-2100 Breakers4Breaker Locations4Location of Local Terminal Connector4Command Definitions4System Commands4SET Command Menu Map4Combiner Cavity4Location of PA Power Potentiometer4Remote Link Installation Checklist5Donor DCCH Channel319BOOSTED DVCC11Boosted DCCH Channel340RF Board To Use For DCCH Channel1Boosted DTC Channel Position 2361Boosted DTC Channel Position 3382Boosted DTC Channel Position 4403Master Password1234Restricted Password5678Dial-up Phone Number 112163498684Auto-dial Trials Max10Modem Mobile MIN1234567890Modem Mobile Power Step7サイズ: 455KBページ数: 93Language: Englishマニュアルを開く