用户手册 — Andrew Wireless Innovations Group RPT-EAC2100

目录

• Introduction

  1
• About This Volume

  1
• 1.1.1 Contents

  1
• 1.1.2 Terminology

  1
• About the TIA/EIA-136 EAC-2100

  1
• 1.2.1 Use of Boosters

  1
• 1.2.2 Frequency Allocation

  1
• 1.2.3 EAC-2100 Operation

  1
• Preliminary Decisions

  2
• Introduction

  2
• Use of Multi-hop Configuration or Multi-donor Units

  2
• Site Requirements

  2
• 2.3.1 Location

  2
• 2.3.2 AC Service

  2
• 2.3.3 Space

  2
• 2.3.4 Mounting Surface

  2
• Antennas

  2
• 2.4.1 Type

  2
• 2.4.2 Placement

  2
• 2.4.3 Measuring Signal Level and Isolation

  2
• Selecting Channels

  2
• 2.5.1 Identifying the Donor DCCH Channel

  2
• 2.5.2 Selecting a Boosted DCCH Channel

  2
• 2.5.3 The Revertive DCCH Channel Option

  2
• 2.5.4 The Substitute DCCH Channel

  2
• • Disabling the Substitute DCCH Channel

  2
• • Enabling the Substitute DCCH Channel

  2
• 2.5.5 Selecting the Directed Retry Channels

  2
• 2.5.6 Selecting Donor DTC Channels

  2
• 2.5.7 Selecting Boosted DTC Channels

  2
• Installing the Hardware

  3
• Introduction

  3
• Mechanical Installation

  3
• 3.2.1 Uncrating the Equipment

  3
• 3.2.2 Mounting the Cabinet

  3
• 3.2.3 Securing the Doors

  3
• Connecting the EAC-2100 to ac Power

  3
• Installing the Antennas

  3
• 3.4.1 Connecting the Antennas

  3
• Connecting External Alarms/Controls (Optional)

  3
• Setting Up for Initial Operation

  4
• Introduction

  4
• Powering Up the EAC-2100

  4
• Powering Down the EAC-2100

  4
• Connecting a Local Terminal

  4
• Becoming Familiar with System Commands

  4
• 4.5.1 Basic Commands

  4
• 4.5.2 Using the SET Menus

  4
• Setting Initial Parameters

  4
• 4.6.1 Checking System Status

  4
• 4.6.2 Entering the Site ID

  4
• 4.6.3 Setting the Donor DCCH Channel

  4
• 4.6.4 Setting the Boosted DCCH Channel

  4
• 4.6.5 Setting the Directed Retry Channels

  4
• 4.6.6 Setting the Donor DTC Channels

  4
• 4.6.7 Setting the Boosted DTC Channels

  4
• 4.6.8 Programming Alarms and Thresholds

  4
• Mobile Power Step, and Passwords

  4
• Tuning Transmitter Combiner and Setting Output Power

  4
• Power Levels for PAs 1− 5 and 7− 11

  4
• 4.7.2 Adjusting the PA 6 Power Level

  4
• 4.7.3 Setting Reverse Path Output Power (If Necessary)

  4
• 4.7.4 Setting PA Power Low Alarm Points

  4
• 4.7.5 Setting Time and Report Values

  4
• Installing the Remote Link

  5
• Introduction

  5
• Setting Up Service

  5
• Programming the Mobile Radio

  5
• Checking Out the Mobile

  5
• Testing the Remote Link

  5
• 5.5.1 EAC-2100 Answering

  5
• 5.5.2 EAC-2100 Originating

  5
• Optimizing Performance

  6
• Introduction

  6
• Determining Hand-in and Hand-back Thresholds

  6
• Setting Hand-in and Hand-back Thresholds

  6
• Important Terms Used in This Manual

  1
• System Operation

  1
• Pre-Installation Checklist

  2
• Recommended Space

  2
• Typical Antenna Installation

  2
• Antenna Isolation v. Horizontal Separation

  2
• Antenna Isolation v. Vertical Separation

  2
• Hardware Installation Checklist

  3
• EAC-2100, Front View (Door Removed)

  3
• EAC-2100, Back View (Door Removed)

  3
• Outdoor Cabinet Footprint

  3
• Antenna Connectors

  3
• External Alarm/Control Connector Pin Out

  3
• Electrical Specifications for Inputs and Outputs

  3
• Typical Wiring for External Inputs and Outputs

  3
• Setup Checklist

  4
• EAC-2100 Breakers

  4
• Breaker Locations

  4
• Location of Local Terminal Connector

  4
• Command Definitions

  4
• System Commands

  4
• SET Command Menu Map

  4
• Combiner Cavity

  4
• Location of PA Power Potentiometer

  4
• Remote Link Installation Checklist

  5
• Donor DCCH Channel

  319
• BOOSTED DVCC

  11
• Boosted DCCH Channel

  340
• RF Board To Use For DCCH Channel

  1
• Boosted DTC Channel Position 2

  361
• Boosted DTC Channel Position 3

  382
• Boosted DTC Channel Position 4

  403
• Master Password

  1234
• Restricted Password

  5678
• Dial-up Phone Number 1

  12163498684
• Auto-dial Trials Max

  10
• Modem Mobile MIN

  1234567890
• Modem Mobile Power Step

  7