ユーザーズマニュアル目次1. SAFETY PRECAUTIONS12. SYSTEM DESCRIPTION12.1 About This Manual12.2 Introduction12.3 System Features52.4 Physical Description62.4.1 Model Types72.4.2 Front Panel82.4.3 Rear Panel Indicators92.4.4 Rear Panel Connections122.4.5 ODU LED Indicators152.5 System Description162.6 Consecutive Point Architecture192.7 2 + 0 (East-West) Configuration212.8 Spanning Tree Protocol (STP)222.9 1+1 Protection222.9.1 Protected Non-Diversity (Hot Standby)222.9.2 Protected Diversity232.10 1 + 1 Multi-hop Repeater Configuration242.11 Data Interfaces252.12 Crosspoint Switch262.13 Power Management272.14 Event-HD Software and Network Management282.14.1 IP Address282.14.2 Network282.14.3 NMS Network Operational Principles292.14.4 Third Party Network Management Software Support302.15 System Loopbacks303. INSTALLATION13.1 Unpacking13.2 Notices23.3 PRE-INSTALLATION NOTES23.4 Back-to-Back Bench Testing23.5 Overview of Installation and Testing Process33.6 Site Evaluation43.6.1 Preparing for a Site Evaluation53.6.2 Site Evaluation Process63.6.3 Critical System Calculations83.6.4 Frequency Plan Determination103.6.5 Antenna Planning133.6.6 ODU Transmit Power Setup143.7 Installation of the Event-HD173.7.1 Installing the Event-HD SDIDUTM173.7.2 Installing the Event-HD ODU183.7.3 Routing the ODU/IDU Interconnect Cable223.8 Quick Start Guide233.8.1 Materials Required233.8.2 Grounding the ODU243.8.3 Grounding the SDIDUTM263.8.4 Connecting the SDIDUTM to the PC and Power Source263.8.5 SDIDU™ Configuration273.8.6 ODU Antenna Alignment303.8.7 Quick Start Settings313.9 SDIDU™ Service323.9.1 Removing a Module333.9.2 Installing a Module344. SUMMARY SPECIFICATION15. REAR PANEL CONNECTORS15.1 DC Input (Power) Connector15.2 Ethernet 100BaseTX Payload Connector 1-215.3 SONET Payload Connector15.4 STM-1 Payload Connector25.5 DVB/ASI, DS-3, E-3, STS-1 Payload Connector25.6 NMS 10/100BaseTX Connector 1-225.7 Alarm/Serial Port Connector35.8 ODU Connector35.9 T1/E1 - Channels 1-2 Connector45.10 T1/E1 - Channels 3-16 Connector45.11 USB65.12 Voice Order Wire75.13 Data Order Wire75.13.1 RS42275.13.2 RS-23286. APPENDIX16.1 Alarm Descriptions1Abbreviations & Acronyms15Conversion Chart17Figure 2-1. Typical Broadcast ENG Application2Figure 2-2. Microwave Split Mount Architecture3Figure 2-2. Event-HD front panel (optional)8Software Defined IDU™, 1+0 Configuration10Connections12Figure 2-4. ODU 2200 RSSI Output vs. Received Signal.15Figure 2-5. Event-HD Block Diagram17Figure 2-6. Ring Configuration20Figure 2-7. Consecutive Point Network21Figure 2-8. 2 + 0 (East West) Configuration22Figure 2-9. 1+1 Protection in Non-Diversity Mode23Figure 2-10. 1+1 Protection in Diversity Mode23Figure 2-11. 1 + 1 Multi-Hop Repeater Configuration25Figure 2-12. Crosspoint Switch26Crosspoint Switch allows access for add/drop.27Figure 2-14. PC and Event-HD SDIDUs™ on Same Subnet292-15. Event-HD SDIDUs™ on Different Subnets303-1. Event HD (1+0) Components13-2. Event-HD Back-to-Back Testing Configuration33-3. Network Deployment Lifecycle43-3. 2 GHz, 12 MHz BAS Frequency Plan103-4. 2 GHz, 17 MHz Legacy BAS Frequency Plan113-6. 7 GHz, 25 MHz BAS Frequency Plan113-7. Event-HD 5.3 GHz Frequency Plan123-8. Event-HD 5.8 GHz Frequency Plan133-8. Software Defined IDU™ Dimensions183-9. ¼-20 threaded mounting hole locations on ODU2200193-10. Pole Mounting Brackets on ODU2200193-11. Completed Pole Mounting of ODU2200203-12. Event ODU5800 Rear View203-13. Tilt Bracket for Event ODU5800213-14. Event ODU5800 with Mounted Tilt Bracket213-15. Completed Mounting for the Event ODU5800223-16. Ground Connections to ODU.253-17. SDIDU DC Power Cable Connector263-18. Software Defined IDU™-SB, 1+1 Protection, Rear Panel Connections273-19. ODU 2200 RSSI Output vs. Received Signal.303-20. ODU RSSI Output vs. Received Signal.313-21. IDU IP address label location323-22. SDIDU™ Modules333-23. Thumbscrew and Corner Screw Locations333-24. Threaded Hole Locations343-25. Guides35Table 2-1. Key Benefits and Advantages of the Event-HD Radios3Table 2-4. DVB-ASI Output status LED.11サイズ: 1.11MBページ数: 102Language: Englishマニュアルを開く