ユーザーズマニュアル目次1640116451OPERATOR’S MANUAL1RHINO®1To the Owner/Operator/Dealer2LOADER1TABLE OF CONTENTS3General Safety Instructions and Practices6Operator Safety Instructions and Practices8Equipment Operation Safety Instructions and Practices10Connecting or Disconnecting Implement Safety Instructions and Practices16Transporting Safety Instructions and Practices17Maintenance and Service Safety Instructions and Practices18Storage and Parking Safety Instructions and Practices20Concluding Safety Instructions and Practices20Decal Location211. D469 1 WARNING Loader Safety222. D468 2 DANGER Crushing, Electrocution, Falling Hazard223. D471 1 WARNING Handling Bales224. 52740 2 WARNING Oil Leaks225. D470 1 DANGER Use ROPS, Seatbelt, Rear Ballast226. 52203 1 WARNING Lock Valve in Transport227. 54283 4 MODEL 1640228. 49696 1 LOGO Rhino, Left229. 51448 1 LOGO Rhino, Right2210. 03200347 * REFLCTR SMV Sign2211. 52204 1 INSTRUCT Loader Positions2212. 00776031 1 __________ Canister, Operator’s Manual2213. 55580 1 __________ Sheet, Decal; includes two D516 Decals (Note: For Optional Quick Attach Device Only)22Decal Description23Federal Laws and Regulations27SAFETY SECTION5Attention Owner/Operator33INTRODUCTION SECTION29ASSEMBLY AND CONNECTING THE LOADER SECTION35Assembly Instructions36Proper Ballasting and Wheel Spacing38General Instructions39Connecting Attachment (Optional)40Dismounting the Loader41Mounting Loader43OPERATION SECTION45RHINO 1640 & 1645 LOADERS46OPERATION INSTRUCTIONS461. Standard Equipment and Specifications47(A) * Maximum Lift Height at Pivot Pin 114”47(B) * Maximum Lift Height under Level Bucket 101.547(C) * Clearance with Bucket Dumped 83”47(D) Reach at Maximum Height 31”47(E) Maximum Dump Angle 73°47(F) Reach with Attachment on Ground 72”47(H) * Digging Depth 5.5”47(U) Lift Capacity to Max Height at Pivot Pin 2,870 lbs47(V) Lift Capacity 800mm Forward of Pivot Pin at Full Height 1,840 lbs47(W) Lift Capacity 800mm Forward of Pivot Pin at 59” 2,350 lbs47(Y) Breakout Force at Pivot Pin 4,440 lbs47Bucket Size and Type 72” SSL Quick Attach472. Operator Requirements483. Tractor Requirements50Tractor Requirements and Capabilities513.1 ROPS and Seat Belt513.2 Tractor Lighting and SMV Emblem513.3 Tractor Ballast513.4 Tractor Ballast and Tire Settings524. Getting On and Off the Tractor524.1 Boarding the Tractor534.2 Dismounting the Tractor535. Starting the Tractor546. Pre-Operation Inspection and Service556.1 Tractor Pre-Operation Inspection/Service556.2 Loader Pre-Operation Inspection and Service567. Driving the Tractor and Loader617.1 Driving the Tractor and Loader628. Operating the Tractor and Loader638.1 Operating the Loader68FILLING THE BUCKET68LIFTING THE LOAD69CARRYING THE LOAD70DUMPING THE BUCKET71LOWERING THE BUCKET71OPERATING WITH FLOAT CONTROL72LOADING FROM A BANK73PEELING AND SCRAPING75LOADING LOW TRUCKS OR SPREADERS FROM A PILE76BACKFILLING77Leave dirt which drifts over side of bucket for final cleanup.79HANDLING LARGE HEAVY OBJECTS791. Using front end loaders for handling large heavy objects such as large round or rectangular bales, logs and oil drums is not recommended.792. Handling large heavy objects can be extremely dangerous due to:793. If you must perform above work, protect yourself by:798.2 Operating Bale Spear808.3 Shutting Down the Implement819. Loader Storage8110. Transporting the Tractor and Implement8110.1 Valve Lock8410.2 Transporting on Public Roadways8510.3 Hauling the Tractor and Implement8611. Troubleshooting Guide87Loader slow or will not lift Hydraulic oil too heavy. Change to proper oil.87and/or dump87Oil filter plugged. Clean or replace filter.87Hydraulic pump worn. Repair or replace pump.87Oil line restricted or leaking. Check all hoses and tubes for leaks,87damage or restrictions. Replace87damaged or restricted hoses or tube87oil lines.87Control valve does not shift Inspect, clean, repair or replace87properly. valve.87Air in hydraulic system. Cycle lift cylinders and bucket87cylinders several times to free87system of air.87Cylinder leaks internally. Replace seals.87Faulty relief valve (tractor). Clean and replace relief valve.87Loader chatters or Air leak in pump inlet line. Check, tighten or replace inlet line.87vibrates when raising87or lowering87Air in hydraulic system. Cycle lift and bucket cylinders.87Oil level too low. Add oil as required.87External leakage Damaged seals. Remove leaking component;87replace seals.87Pump noisy Inlet line restricted or leaking. Check for air leaks, restrictions or87collapsed hose. Tighten or replace hose. Clean filter.87Oil level too low. Add oil as required.87Pump worn or damaged. Repair or replace pump.87Excessive wear on bucket Bucket is riding on cutting edge Use boom “FLOAT” position or87cutting edge instead of wear runners. bucket level indicator to ensure87bucket rides on wear runners.87MAINTENANCE SECTION89Daily Maintenance931. Check fluid level of tractor hydraulic system before starting each day’s operation. If necessary, add hydraulic oil as recommended in your tractor operator’s manual.932. After every four hours of operation, lubricate all sixteen grease fittings933. After every ten hours of operation, check all hardware and tighten where required.934. Replace hoses immediately if they are damaged by a cut or scrape, extruded at the fittings or leaking. Hydraulic oil leaks should be repaired promptly to avoid loss of oil and serious personal injury from escaping oil.93Storage941. Store loader with attachment securely attached.942. Place dust caps on hydraulic quick couplers.943. Do not remove attachment from stored loader.954. Do not allow children to play on or around loader.95Proper Torque for Fasteners961640 & 1645102LOADER102RHINO100LIMITED WARRANTY1001. LIMITED WARRANTIES1001.01. Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the ...1001.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.1001.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, ...1001.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.1002. REMEDIES AND PROCEDURES.1002.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase.1002.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based1002.03. Purchaser is responsible for returning the goods in question to the Dealer.1002.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will:100(a) Repair or replace the defective goods or part(s) or100(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer.1002.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for...1003. LIMITATION OF LIABILITY.1003.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.1003.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS.1003.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLU...1003.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.1004. MISCELLANEOUS.1004.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.1004.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.1004.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.1004.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.100TO THE OWNER/OPERATOR/DEALER101RHINO®100サイズ： 8.99MBページ数： 102Language: Englishマニュアルを開く
