Vermont Casting 2822 사용자 설명서

12

12

Vermont Castings Jefferson Direct Vent/Natural Vent Gas Heater

20002191

The Stardance Heater must be vented to the outdoors
through an adjacent exterior wall or through the roof.
The venting system must be comprised of the appropri-
ate listed venting components specified on this page.
These parts are available from DuraVent Corporation or
your Vermont Castings Majestic Products Dealer.

See Figure 4 for dimensions relevant to the standard
minimum-vent kits.

Starter Pipe Assembly (incl. inner & outer sections)
2768*
90

°

 Elbow, Blk.

990B*

45

°

 Elbow, Gal.

945

6” Straight, Blk.

908B*

9” Straight, Blk.

907B

11” - 14

⁵⁄₈

” Adjustable Straight Section

911B

12” Straight

906

24” Straight

904B*

36” Straight

903B

48” Straight

902

Horizontal Vent Cap

984*

Wall Plate*

940

Vinyl Siding Shield

950

Snorkel Termination - 14”

982

Snorkel Termination - 36”

981

Wall Strap

988

Cathedral Ceiling Support Box

941

Storm Collar

953

Firestop Spacer

963

Flashing 0/12 - 6/12

943

Flashing 6/12 - 12/12

943S

Vertical Termination Cap

991

*Included in Minimum Horizontal Vent Kit #2792

All DuraVent Straight vent pipe sections have a net
length 1

¹⁄₂

” (37mm) less than the nominal dimension;

i.e., a 6” (152mm) Straight pipe section has an
effective length of 4

¹⁄₂

” (115mm).

The following kits are available to meet the needs of
most installations. All pipe has a 7" outer diameter and
includes a 4" diameter inner section. A (CG) designa-
tion indicates the part is finished in Charcoal Gray
paint. Consult your dealer about other vent parts that
may be appropriate to complete the installation.

(1) 90-Degree Elbow (CG)
(1) 24" Straight pipe (CG)
(1) 36" Straight pipe (CG)
(1) Side Wall Termination
(1) Firestop
(1) Zero-clearance sleeve
(1) Hardware package

(1) Finishing plate (CG)
(1) Finishing collar (CG)
(4) Polished Brass flue pipe rings
Through the Wall Vent Kit

(1) 90-Degree Elbow (CG)
(1) 24" Straight pipe (CG)
(1) 48" Straight pipe (CG)
(1) Side Wall Termination
(1) Firestop
(1) Zero-clearance sleeve
(1) Hardware package
(1) Finishing plate (CG)
(1) Finishing collar (CG)
(4) Polished Brass flue pipe rings
Through the Wall Vent Kit for
Below-Grade Termination

Includes all of the above parts plus
(1) Snorkel Termination
Vertical Termination Kit, 1/12-6/12 Pitch

(1) Combination Horizontal Offset  / Roof Support
(1) Vertical Termination
(1) Storm Collar
(1) 1/12-6/12 Flashing
(1) Finishing Plate (CG)
(1) Finishing Collar (CG)
(1) Polished Brass Flue Pipe Ring
(1) Hardware Package
Vertical Termination Kit, 7/12-12/12 Pitch

(1) 7/12 - 12/12 Flashing
and all of the other Vertical Termination parts.
Vertical Termination, Flat Roof

(1) Flat Flashing
and all of the other Vertical Termination parts.
Twist Lock 24" Straight Pipe (CG)

(1) 24" Non-adjustable Pipe
(1) Polished Brass Flue Pipe Ring
Twist Lock 48" Straight Pipe (CG)

(1) 48" Nonadjustable Pipe
(1) Polished Brass Flue Pipe Ring
Twist Lock 45-Degree Elbow (CG)

for vertical offsets
(1) 45-degree Elbow
(1) Polished Brass Flue Pipe Ring
Draft Hood Adapter

(1) 7” Diameter Polished Brass Trim Ring
(1) 48” Nonadjustable Pipe (CG)
(1) 24” Nonadjustable Pipe (CG)
(1) Finishing Plate
(1) Finishing Collar (CG)
(1) 90 Degree Elbow (CG)
Stove Kit

Includes all parts in the 7FSSK plus the Draft Hood Adapter
FSDHAG
Combination Offset/Roof Support

NOTE: Direct vent pipe may be used on the Natural
Vent system from the top of the draft hood adapter to
the ceiling.