Quadra-Fire CASTINS-CSB 사용자 설명서
R
August 20, 2009
250-7251G
Page 7
Castile Pellet Insert
G. Inspect Appliance & Components and
Pre-Use Check List
Reciprocating Saw
Hammer
Phillips Screw driver
Tape Measure
Plumb Line
Level
Framing Material
Hi-temp Caulking Material
Gloves
Hammer
Phillips Screw driver
Tape Measure
Plumb Line
Level
Framing Material
Hi-temp Caulking Material
Gloves
Safety Glasses
Framing Square
Electric Drill & Bits (1/4”)
1/4” Self-Tapping Screws
Framing Square
Electric Drill & Bits (1/4”)
1/4” Self-Tapping Screws
May also need:
Vent Support Straps
Venting Paint
Vent Support Straps
Venting Paint
Tools and building supplies normally required
for installation, unless installing into an existing
masonry fi replace:
for installation, unless installing into an existing
masonry fi replace:
F. Tools And Supplies Needed
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
damage. Damaged parts may impair safe
operation.
WARNING
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
1.
Place the appliance in a location near the
fi nal installation area and follow the proce-
dures below:
fi nal installation area and follow the proce-
dures below:
2.
Open the appliance and remove all the parts
and articles packed inside the Component
Pack. Inspect all the parts and glass for ship-
ping damage. Contact your dealer if any irregu-
larities are noticed.
and articles packed inside the Component
Pack. Inspect all the parts and glass for ship-
ping damage. Contact your dealer if any irregu-
larities are noticed.
3.
All safety warnings have been read and fol-
lowed.
lowed.
4.
This Owner’s Manual has been read.
5.
Floor protection requirements have been met.
6.
Venting is properly installed.
7.
The proper clearances from the appliance and
chimney to combustible materials have been
met.
chimney to combustible materials have been
met.
8.
The masonry chimney is inspected by a profes-
sional and is clean, or the factory built metal
chimney is installed according to the manufac-
turer’s instructions and clearances.
sional and is clean, or the factory built metal
chimney is installed according to the manufac-
turer’s instructions and clearances.
9.
The chimney meets the required minimum
height.
height.
10.
All labels have been removed from the glass
door.
door.
11.
Plated surfaces have been wiped clean, if
applicable.
applicable.
12.
Thermostat or remote has been installed.
13.
A power outlet is available nearby.
14.
A good quality surge protection is highly recom-
mended to protect the electronics.
mended to protect the electronics.
• Installation and use of any damaged appliance.
• Modifi cation of the appliance.
• Installation other than as instructed by Hearth & Home
• Modifi cation of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
• Operating appliance without fully assembling all
components.
• Do NOT Overfi re.
Or any such action that may cause a fi re hazard.
WARNING
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
responsibility for, and the warranty will be
voided by, the following actions:
Fire Risk.
E. Fire Safety
To provide reasonable fi re safety, the following should be
given serious consideration:
given serious consideration:
• Install at least one smoke detector on each fl oor of your
home.
• Locate smoke detector away from the heating appliance
and close to the sleeping areas.
• Follow the smoke detector manufacturer’s placement and
installation instructions and maintain regularly.
• Conveniently locate a Class A fi re extinguisher to contend
with small fi res.
• In the event of a hopper fi re:
• Evacute the house immediately.
• Notify fi re department.