Hoover Bagless Upright Vacuum Cleaner 사용자 설명서
13
Clearing blockages
Disconnect cleaner from electrical
outlet.
outlet.
Low suction or pick up may be due to a
blockage in the system. Refer to the fol-
lowing steps to check for blockages
blockage in the system. Refer to the fol-
lowing steps to check for blockages
continuing with each step until the
blockage is found:
blockage is found:
Turn cleaner OFF and disconnect from
electrical outlet.
1. Check fullness of dirt cup and filter
assembly; empty cup and clean filters if
needed.
electrical outlet.
1. Check fullness of dirt cup and filter
assembly; empty cup and clean filters if
needed.
4-2
D
A
C
B
Check airflow path
4. Plug cleaner in and turn ON. Check
for suction at end of hose (B).
for suction at end of hose (B).
a. If there is
suction,
continue with
step 5.
4-3
E
Checking under bottom plate
6. Turn cleaner OFF and unplug.
7. Remove bottom plate, belt and agita-
tor (see “The belt” section).
7. Remove bottom plate, belt and agita-
tor (see “The belt” section).
Look into opening (E) for blockages and
remove.
remove.
8. Remove agitator shield (see Fig. 3-21)
and remove any loose debris which may
have accumulated under it.
and remove any loose debris which may
have accumulated under it.
4-1
Check dirt duct
2. Remove dirt cup, look in duct (A).
3. Clear blockage from dirt duct.
3. Clear blockage from dirt duct.
4. If you have a
problem
problem
If a minor problem occurs, it usually can
be solved quite easily when the cause is
found by using the check list below.
be solved quite easily when the cause is
found by using the check list below.
Problem: Cleaner won’t run
Possible cause
Possible solution
• Not firmly plugged in
•
•
Plug unit in firmly
• No voltage in wall plug
•
•
Check fuse or breaker
• Blown fuse or tripped breaker
•
•
Replace fuse or reset breaker
• Thermal protector activated
•
•
Allow cleaner to cool for 30 minutes
(this will reset the thermal protector)
(see pg. 12).
(see pg. 12).
Prob
Problem: Cleaner won’t pick up
Possible cause
Possible solution
• Broken or worn belt
•
•
Replace belt
• Agitator brush roll worn
•
•
Replace brush roll
• Dirt cup full
•
•
Empty cup
• Incorrect carpet height setting
•
•
Move nozzle control knob to lower
setting
• Blockage in air flow passage
•
•
Clear blockage
• Pleated filter clogged
•
•
Clean pleated filter by either tapping
the side of the dirt cup or removing the
filter as described in the “Filter assem-
bly” section
filter as described in the “Filter assem-
bly” section
• Pre-filter clogged
•
•
Clean pre-filter as described in “Filter
assembly” section
• Dirt cup not properly installed
•
•
Position dirt cup properly and snap in
place (Fig. 3-4)
• Dirt cup lid not positioned properly
or missing
•
Ensure that dirt cup lid is properly
positioned
• Filter assembly not installed
properly
•
Ensure that pre-filter assembly and
pleated filter are positioned properly
(Figs. 3-9 to 3-10)
(Figs. 3-9 to 3-10)
Problem: Cleaner hard to push
Possible cause
Possible solution
• Incorrect carpet height setting
•
•
Move nozzle control knob to a
higher setting
higher setting
Problem: Cleaning tools won’t pick up
Possible cause
Possible solution
• Dirt cup not properly installed
3) Look into (D) and remove block-
age.
age.
5. Check connection at hose tube (C);
remove any blockage.
remove any blockage.
•
Position dirt cup properly and snap in
place (Fig. 3-4)
• Blockage in hose
•
•
Clear blockage
Problem: Visible dirt leaking through
final filter
Possible cause
Possible solution
• Filter assembly not installed
properly
•
Ensure that pre-filter assembly and
pleated filter are positioned properly
Problem: Smoky/burning smell
detected
detected
Possible cause
Possible solution
• Belt broken or stretched
•
•
Replace agitator brush roll belt as
described in Figs. 3-18 through 3-23 in
the Maintenance section.
the Maintenance section.
b. If there is
no suction,
check for
blockage in hose and dirt tube as
follows:
follows:
1) DIsconnect hose from dirt duct
(D) by reversing procedure for
“Attach hose” (Fig. 1-8 and 1-9).
2) Clear out hose.
(D) by reversing procedure for
“Attach hose” (Fig. 1-8 and 1-9).
2) Clear out hose.