Land Pride AR2510 사용자 설명서
9
Section 1: Assembly & Set-up
12/09/15
AR2596 & AR2510 Pasture Aerators 325-127M
3.
Install orifice plug (#12) into the cylinder port located
near the base end of hydraulic cylinder (#11). Screw
plug in until orifice bottoms out. Do not tighten.
near the base end of hydraulic cylinder (#11). Screw
plug in until orifice bottoms out. Do not tighten.
4.
Screw elbow fittings (#9A & #9B) into both cylinder
ports with O-rings facing ports. Do not tighten elbows
until step #17.
ports with O-rings facing ports. Do not tighten elbows
until step #17.
5.
Attach base end of hydraulic cylinder (#11) to the
Aerator’s main frame (#3) with 1" x 3 11/16" clevis
pin (#10). Secure pin with hairpin cotter (#8).
Aerator’s main frame (#3) with 1" x 3 11/16" clevis
pin (#10). Secure pin with hairpin cotter (#8).
6.
Attach rod end of hydraulic cylinder (#11) to axle
assembly (#1) with 1" x 2 3/4" clevis pin (#6). Secure
clevis pin with cotter pin (#7). Bend one or more legs
on the cotter pin to keep it from falling out.
assembly (#1) with 1" x 2 3/4" clevis pin (#6). Secure
clevis pin with cotter pin (#7). Bend one or more legs
on the cotter pin to keep it from falling out.
Refer to Figure 1-4:
7.
7.
Attach 3/4" adapter (#18) to hydraulic
hoses (#13 & #14) and tighten.
hoses (#13 & #14) and tighten.
8.
Attach quick disconnect couplings (#19) to
adapters (#18) and tighten.
adapters (#18) and tighten.
Refer to Figure 1-3:
9.
9.
Insert the longer (201") hydraulic hose (#14) into the
back opening end of the Aerator tongue. Push hose
through tongue and out its front opening.
back opening end of the Aerator tongue. Push hose
through tongue and out its front opening.
10. Install flex guard (#15) over hydraulic hose (#14) at
the cylinder end and push flex guard halfway into the
tongue to protect hydraulic hose from wear.
tongue to protect hydraulic hose from wear.
11. Attach hydraulic hose (#14) to elbow fitting (#9B) and
tighten.
12. Insert the shorter (185") hydraulic hose (#13) into the
back opening end of the Aerator tongue. Push hose
through tongue and out its front opening.
through tongue and out its front opening.
13. Install flex guard (#15) over hose (#13) at the cylinder
end and push flex guard halfway into the tongue to
protect hydraulic hose from wear.
protect hydraulic hose from wear.
14. Attach hydraulic hose (#13) to elbow fitting (#9A) and
tighten.
Refer to Figure 1-4:
15. Pull hydraulic hoses (#13 & #14) out of opening (#17)
15. Pull hydraulic hoses (#13 & #14) out of opening (#17)
until most of the slack in the hoses at the hydraulic
cylinder have been removed.
cylinder have been removed.
16. Run hydraulic hoses through hose loop (#16).
Refer to Figure 1-3:
17. Orient elbows (#9A & #9B) to suit and tighten to
17. Orient elbows (#9A & #9B) to suit and tighten to
hydraulic cylinder (#11).
Slow Moving Vehicle Sign (SMV)
Refer to Figure 1-5:
1.
1.
Bolt SMV sign (#3) to mounting blade (#4) as shown
with 1/4"-20 x 5/8" GR5 hex flange screws (#1) and
hex flange nuts (#2). Tighten nuts to the correct
torque.
with 1/4"-20 x 5/8" GR5 hex flange screws (#1) and
hex flange nuts (#2). Tighten nuts to the correct
torque.
2.
Insert mounting blade (#4) into mounting socket (#5).
Rear Axle & Lift Cylinder Assembly
Figure 1-3
Hydraulic Hose Routing & Quick Coupling Assembly
Figure 1-4
Slow Moving Vehicle Sign Assembly
Figure 1-5
30060
Grease Zerk
Grease Zerk
30061
30062