Maxim RMT50B 사용자 설명서

  

bolts, nuts and lock washers.  The left brace bolts between the belt guard bracket and the transmission.  
The braces are mounted to the handle bars using one 1/4” - 20 x 1 1/2 and one 1/4” - 20 x 1 3/4” hex bolts, 
nuts, and lock washers.  The clutch cable guide mounts on the outside of the right handle bar.  Route the 
clutch cable through guide with the adjustment at the top.  See Figure 1.
6.  Install the handle bar cross brace between the handle bars using four 1/4” - 20 x 1 1/2” hex bolts, nuts, 
and lock washers.  See Figure 1.
7.  Route the throttle control cable under the handle passing under the cross brace.
8.  Tighten all bolts at this time.
9.  Install clutch cable by hooking loop at bottom into notch in clutch arm.  Hook spring into clevis and into 
hole in clutch lever.  The clutch cable should be adjusted so that the belt will slip when released and the 
spring will be extended 1/4” when lever is engaged.
10.  Install handle bar grips (Some type of lubricant such as liquid soap will be helpful).
FINAL SETUP
1.  Check the transmission to that it is full. See Figure 3.
 

a.  Remove check plug.

 

b.  Use 90 wt. gear lube or 50 weight motor oil.   

 

 

Approximately 1 pint.

 

c.  Fill until check plug overflows.

 

d.  Replace plug.

2.  Remove the engine dipstick and fill crankcase with oil ac-
cording to engine owner’s manual.
3.  Fill fuel tank.  Use clean, fresh, lead-free, gasoline.  Fill 
the tank completely.  
DO NOT MIX OIL WITH GASOLINE.

right as you stand in an operating position.  See Figure 1 and 2.
5.  Install the two handle bar tie braces between the holes in the transmission and the lower holes in the 
handle bars.  Fasten the braces to the transmission using one 5/16” - 18 x 1” and one 5/16” x 1 1/4” hex 

Ref#

Part #

Quan.

Description

Part #

Quan

Description

101

336682

1

Main Frame Rail LH

102

336681

1

Main Frame Rail RH

103

359335

2

Frame Spacer

302

130695

1

Handle Bar LH

162081

1

Handle Bar Left Hand

303

336678

2

Handle Bar Brace

304

130730

1

Handle Cross Brace

305

313786

2

Handle Grip

4

308

130694

1

Handle Bar Right Hand

162082

1

Handle Bar RH Heavy Duty

402

162077

1

Intek Throttle Control

403

402014

2

#10 - 3/8” Slot Tapping Screw

404

336683

1

Clutch Lever

405

359345

1

Clutch Lever Pin

407

359346

1

Clutch Locking Pin

408

359359

1

Clutch Locking Spring

409

359327

1

Clutch Cable Spring

410

162041

1

Clutch Cable and Adjustment

413

359326

2

Clutch Cable Guide

414

359323

1

Throttle Cable Clip

601

162031

2

Wheel, 10” x 1.75

162065

2

Wheel, 10” x 1.75” Heavy Duty

605

461467

1

Wheel Yoke Locking Pin

606

359362

1

Lock Pin Spring

607

461468

1

Cotter Pin

609

162032

1

Wheel Yoke Assembly

162033

1

Wheel Yoke Assembly

615

130701

2

Hitch Casting

618

336686

1

Depth Bar

621

359363

1

Depth Bar Adjust. Spring

625

461469

1

Depth Bar Adjust. Pin

705

359321

1

Idler Pulley

338009

1

Idler Pulley

706

162069

1

Idler Shaft

708

359325

1

Idler Shaft Arm

709

400290

1

Capscrew NC, 3/8” x 1 3/4”

802

359330

2

Wheel Shoulder Bolt

804

400184

2

Cap Screw, NC 5/16” x 3/4”

805

400186

1

Cap Screw, NC 5/16” x 1”

400190

Cap Screw, NC 5/16” x 1 1/4”

806

400197

1

Cap Screw, NC 5/16” x 2 1/4”

807

400200

4

Cap Screw, NC 5/16” x 2 1/2”

809

400207

2

Cap Screw, NC 5/16” x 3 3/4”

811

400275

1

Cap Screw, NC 3/8” x 3”

813

400115

5

Cap Screw, NC 1/4” x 1 1/2”

814

400109

1

Cap Screw, NC 1/4” x 1 3/4”

816

443101

6

Nut, NC 1/4”

817

443106

11

Nut, 5/16”

818

443110

2

Nut NC, 3/8”

819

444721

4

Locknut NC, 3/8”

820

444720

1

Locknut NF, 3/8”

821

446130

6

Lockwasher, 1/4”

822

446136

11

Lockwasher, 5/16”

825

455050

1

Washer SAE Flat, 1/2”

830

162096

Optional

LH Tine Shield

831

162095

Optional

RH Tine Shield

833

359853

1

Engine Guard