Maxim RMT50B 사용자 설명서
OPERATION
BEFORE USING THIS MACHINE CHECK THE ASSEMBLY INCLUDING
THE HANDLE AND CONTROLS. MAKE SURE ALL FASTENERS ARE
TIGHT. MAKE SURE THE THROTTLE AND OTHER CONTROLS WORK
CORRECTLY.
THE HANDLE AND CONTROLS. MAKE SURE ALL FASTENERS ARE
TIGHT. MAKE SURE THE THROTTLE AND OTHER CONTROLS WORK
CORRECTLY.
BEFORE STARTING THIS TILLER, BE FAMILIAR WITH ALL OPERAT-
ING CONTROLS. KNOW HOW TO DISENGAGE TINES, STOP FORWARD
MOVEMENT AND SHUT OFF ENGINE.
ING CONTROLS. KNOW HOW TO DISENGAGE TINES, STOP FORWARD
MOVEMENT AND SHUT OFF ENGINE.
OPERATING CONTROLS
Throttle Control Lever
The throttle control lever, located on the left side of the handle controls engine speed. When starting, place
control lever in center position. Then adjust to desired speed. To stop engine move throttle control lever to
rear position. Push stop switch at spark plug.
Clutch Lever
The clutch is disengaged when clutch is away from handle grip. To engage clutch, squeeze clutch lever to
handle.
Operating Instructions
Before operating the machine, become familiar with the operating instructions and safety suggestions in this
manual. Operate the machine in an open area to get the “feel” of the machine and its controls.
Starting and Stopping the Engine
Before starting the engine check that all bolts are tight, and that the tiller is assembled properly. Review
Safety suggestions and Operating Instructions for safe and proper use of the tiller.
Pre Start
The throttle control lever, located on the left side of the handle controls engine speed. When starting, place
control lever in center position. Then adjust to desired speed. To stop engine move throttle control lever to
rear position. Push stop switch at spark plug.
Clutch Lever
The clutch is disengaged when clutch is away from handle grip. To engage clutch, squeeze clutch lever to
handle.
Operating Instructions
Before operating the machine, become familiar with the operating instructions and safety suggestions in this
manual. Operate the machine in an open area to get the “feel” of the machine and its controls.
Starting and Stopping the Engine
Before starting the engine check that all bolts are tight, and that the tiller is assembled properly. Review
Safety suggestions and Operating Instructions for safe and proper use of the tiller.
Pre Start
Figure 4
DANGER
To avoid possible serious bodily
injury, keep hands and feet
away from tines and v-belt be-
fore and after starting engine.
injury, keep hands and feet
away from tines and v-belt be-
fore and after starting engine.
1. Check the spark plug for proper connection on the spark
plug.
2. Fill the fuel tank with clean, fresh, regular gasoline from
an approved container.
3. Check the oil for proper level. Refer to engine owner’s
manual for correct grade and quantity and directions.
4. Make certain clutch lever is in disengaged position.
Starting Procedure
1. Move throttle control lever to center position.
2. Manually open choke. Hold the handle with your left
hand while pulling the starter rope with your right. Pull the
rope out slowly until the engine reaches the start of the
compression cycle (the rope will pull slightly harder at this
point). Then allow the rope to retract fully.
3. Pull the rope with a continuous full arm stroke. Keep
a firm grip on the starter handle and let the rope rewind
slowly. Do not let the handle snap back against the starter.
plug.
2. Fill the fuel tank with clean, fresh, regular gasoline from
an approved container.
3. Check the oil for proper level. Refer to engine owner’s
manual for correct grade and quantity and directions.
4. Make certain clutch lever is in disengaged position.
Starting Procedure
1. Move throttle control lever to center position.
2. Manually open choke. Hold the handle with your left
hand while pulling the starter rope with your right. Pull the
rope out slowly until the engine reaches the start of the
compression cycle (the rope will pull slightly harder at this
point). Then allow the rope to retract fully.
3. Pull the rope with a continuous full arm stroke. Keep
a firm grip on the starter handle and let the rope rewind
slowly. Do not let the handle snap back against the starter.
FRAME ASSEMBLY
5
12