Hitachi SJ300-037HFE 사용자 설명서

다운로드
페이지 289
SJ300 Inverter Specifications
Geting Star
ted
1–10
Signal Ratings
Detailed ratings are in 
Other user-settable parameters
V/F free-setting (up to 7 points), frequency upper/lower limit, frequency jump, accel/
decel curve selection, manual torque boost value and frequency adjustment, analog 
meter tuning, start frequency, carrier frequency, electronic thermal protection level, 
external frequency output zero/span reference, external frequency input bias start/end, 
analog input selection, retry after trip, restart after instantaneous power failure, various 
signal outputs, reduced voltage start, overload restriction, default value setting (US, 
Europe, Japan), deceleration and stop after power failure, AVR function, fuzzy accel/
decel, auto-tuning (on-line/off-line), high-torque multi-operation, automatic energy-
saving operation
Carrier frequency range
0.5 to 15 kHz
Protective functions
Over-current, overload, braking resistor overload, over voltage, EEPROM error, under-
voltage error, CT (current transformer) error, CPU error, external trip, USP error, 
ground fault, input over voltage, instantaneous power failure, expansion card 1 error, 
expansion card 2 error, inverter thermal trip, phase failure detection, IGBT error, 
thermistor error
Environ-
ment
Temperature (*9)
Operating (ambient): -10 to 50
°C / Storage: -20 to 65°C
Humidity
20 to 90% humidity (non-condensing)
Vibration  *10
Models SJ300–004xxx to 220xxx:  5.9 m/s
2
 (0.6G), 10 to 55 Hz
Models SJ00–300xx to 1500xxx: 2.94 m/s
2
 (0.3G), 10 to 55 Hz
Location
Altitude 1,000 m or less, indoors (no corrosive gasses or dust)
Coating color
Gray
Accessories Feedback PCB
SJ-FB (vector control loop speed sensor)
Digital input PCB
SJ-DG (4-digit BCD / 16-bit binary)
Others
EMI filters, input/output reactors, DC reactors, radio noise filters, braking resistors, 
braking units, LCR filter, communication cables, factory I/O network interface cards
Operator input devices
OPE–SRE (4-digit LED with potentiometer) / OPE–S (4-digit LED w/o potentiometer), 
Optional: OPE-SR (4-digit LED with potentiometer, Japanese/English overlay),
SRW–0EX Multilingual operator with copy function (English, French, German, Italian, 
Spanish, and Portuguese)
Item
General Specifications
Signal / Contact
Ratings
Built-in power for inputs
24VDC supply, 100 mA maximum
Intelligent (programmable) logic inputs
27VDC maximum,  4.7k
Ω input impedance
Intelligent (programmable) logic outputs
Open collector type, 50mA max. ON state current, 27 VDC maximum OFF state voltage
Thermistor input
Minimum thermistor power 100mW
PWM output
0 to 10VDC, 1.2 mA max.,  50% duty cycle
Voltage analog output
0 to 10VDC, 2 mA max.
Current analog output
4-20 mA, nominal load impedance 250
Ω
Analog input, current
4 to 19.6 mA range, 20 mA nominal
Analog input, voltage
0 to 9.6 VDC range, 10VDC nominal, 12VDC max., input impedance 10 k
Ω
+10V analog reference
10VDC nominal, 10 mA maximum
Alarm relay, normally closed contacts
Maximum loads: 250VAC, 2A; 30VDC, 8A resistive load
   250VAC, 0.2A; 30VDC, 0.6A inductive load
Minimum loads: 100 VAC, 10mA; 5VDC, 100mA
Alarm relay, normally open contacts
250VAC, 1A; 30VDC 1A max. resistive load / 
   250VAC, 0.2A; 30VDC, 0.2A max. inductive load
Min. loads: 100 VAC, 10mA; 5VDC, 100mA