Netgear WG111T 전단

)NSTALLATION

These basic setup instructions assume that you will connect to an access point, and you are 
not using WEP security. Please refer to the online help and the Reference Manual on your 
CD for instructions on configuring security, Ad-hoc mode, or advanced options.
Estimated Completion Time: 5-15 minutes for a notebook PC.

You can attach the WG111T Wireless USB 2.0 Adapter 
directly to a USB port on your computer, or use the USB 
cable to extend the range and obtain better wireless 
reception. 
Follow these instructions to use the USB cable, plastic 
cradle, and velcro provided in the package for better USB 
Adapter placement on a notebook or desktop computer:

1. The WG111T Wireless USB 2.0 Adapter comes with 

3 pieces of velcro. Locate the one that has a prickly side and 
attach it to the plastic cradle on the middle of the outside rear.

2. Insert the WG111T Wireless USB 2.0 Adapter in the plastic 

cradle.

3. Place one of the other pieces of velcro on the back of your 

notebook monitor near the top for better reception.
Note: The last piece of velcro can be placed on the side of your PC monitor nearest 
your wireless access point, if you are using the USB Adapter with a desktop PC.

4. Join the pieces of velcro to attach the USB Adapter in the plastic cradle to the 

notebook or desktop monitor.

See the installation instructions for your operating system before attaching the USB cable 
to the USB Adapter and your computer.

a.

Power on your PC, let the operating system boot up completely, and log in as 
needed. 

b. Insert the Resource CD for the WG111T into 

your CD-ROM drive. The CD main page 
shown below will load. 

c.

Click the Install Driver & Utility link. 

d. Follow the InstallShield Wizard steps. You will 

be prompted to choose the country you are 
located in. 

e.

Click Finish when done. If prompted by a Found New Hardware Wizard to 
install a “bootloader device,” do so. Restart your computer, if prompted.

a.

Locate an available USB port on your PC. Connect the USB cable to the 
WG111T and insert the other end of the cable into the USB slot on your PC.

b. After a short delay, 

the Found New 
Hardware Wizard 
displays. Select 
Install the software 
automatically 
(Recommended) and 
click Next.

c.

Next you will be 
prompted to enable 
the NETGEAR Smart Wireless Settings Utility configuration utility. 
Click Yes to accept this option. 
If you choose No, you must 
read the Windows XP 
documentation for an 
explanation of how to use the 
Windows XP wireless network 
configuration utility.

Note: If a Windows 
XP logo testing 
warning appears, click 
Continue Anyway to 
proceed. 

You will also be prompted to choose the country you are located in. Select 
your location from the list.

d. Click Finish to complete the installation. You will see the 

WG111T system tray icon on the lower right portion of the 
Windows task bar.

a.

Click the 

 icon in the Windows system tray to open the WG111T Smart 

Wireless Settings Utility.
The utility opens to the 
Settings tab page. 

b. Change the Network 

Name SSID to match 
your network.
Tip: To view the 
available wireless networks, use the drop-down list or the Networks tab and 
choose the one you want.

c.

Click Apply to activate the connection.
Tip: Create work and home profiles. Then, activate whichever one you need for 
your current location.

a.

Verify that the status monitor information at the bottom of the utility matches 
your wireless network.

b. Check the color of the WG111T icon in the Windows system tray: green or 

yellow indicates a working connection; red indicates no connection.

c.

Check the WG111T LED: blinking means attempting to connect; solid indicates a 
good connection; off means the WG111T is not plugged in. 

d. Verify connectivity to the Internet or network resources.

Note: If you are unable to connect, see the Troubleshooting chapter of the 
Reference Manual on the NETGEAR 108 Mbps Wireless USB 2.0 Adapter 
WG111T Resource CD.