Netgear WG111T 전단

Note: Windows 2000 may require you to be logged on with administrator rights.
a.

Power on your PC, let the operating system boot up completely, and log in as 
needed. 

b. Insert the Resource CD for the WG111T into 

your CD-ROM drive. The CD main page 
shown below will load. 

c.

Click the Install Driver & Utility link. 

d. Follow the InstallShield Wizard steps. You 

will be prompted to choose the country you are 
located in. 

e.

Click Finish when done. If prompted by a Found New Hardware Wizard to 
install a “bootloader device,” do so. Restart your computer, if prompted.

a.

Locate an available USB port on your PC. Connect the USB cable to the 
WG111T and insert the other end of the cable into the USB slot on your PC.

b. After a short delay, the Found New Hardware Wizard displays. Select Install the 

software automatically (Recommended) and click Next.

c.

Follow the Found New 
Hardware Wizard 
steps, click Finish 
when done, and if 
prompted, restart your 
computer.

Note: If Windows 
2000 displays a 
Digital Signature 
Not Found warning, 
click Yes to 
continue the 
installation. 

d. Next, you will be prompted to choose the country where you are located. Select 

your location from the list.
You will now see the WG111T system tray icon in the lower right area of 
the Windows task bar.

a.

Open the WG111T 
Smart Wireless 
Settings Utility by 
clicking on the icon in 
the Windows system 
tray.
The utility opens to the Settings tab page. 

b. Change the Network Name SSID to match your network.

Tip: To view the available wireless networks, use the drop-down list or the 
Networks tab and choose the one you want.

c.

Click Apply to activate the connection.
Tip: Create work and home profiles. Then, activate whichever one you need for 
your current location.
Note: The status bar at the bottom of the utility reports the speed of your 
connection. 108 Mbps speed is only possible when your wireless network has a 
108 Mbps access point such as in the NETGEAR WGT624 108 Mbps Wireless 
Firewall Router.

a.

Verify that the status monitor information at the bottom of the utility matches 
your wireless network.

b. Check the color of the WG111T icon in the Windows system tray: green or 

yellow indicates a working connection; red indicates no connection.

c.

Check the WG111T LED: blinking means attempting to connect; solid indicates a 
good connection; off means the WG111T is not plugged in. 

d. Verify connectivity to the Internet or network resources.

Note: If you are unable to connect, see the Troubleshooting chapter of the 
Reference Manual on the NETGEAR 108 Mbps Wireless USB 2.0 Adapter 
WG111T Resource CD. 

PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH 
YOUR PRODUCT.
By registering your product at www.NETGEAR.com/register, we can provide you with 
timely expert technical support.
NETGEAR, INC. Support Information
Phone: 1-888-NETGEAR (For US & Canada only) - 24 x7 phone support. See Support 
Information card for other countries.
E-mail: support@NETGEAR.com - 24 x 7 online support.

©2004 NETGEAR, Inc. NETGEAR, the Netgear logo and Everybody's connecting are 
trademarks or registered trademarks of Netgear, Inc. in the United States and/or other 
countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in 
the United States and/or other countries. Other brand and product names are trademarks or 
registered trademarks of their respective holders. Information is subject to change without 
notice. All rights reserved. 

Attention: This device may be used throughput the European 
Community, except restrictions apply in some regions of France. 
Please see the Reference Manual on the NETGEAR 108 Mbps Wireless 

USB 2.0 Adapter WG111T Resource CD for details.