Netgear WN802Tv2 전단

)NSTALLATION

Follow these instructions to set up your wireless-N access point

. You can also consult the 

documentation links on the Resource CD or the NETGEAR knowledge base at 
http://kbserver.netgear.com. Please consult the Resource CD or the Documentation link on 
the user interface to access the Reference Manual for instructions on advanced 
configuration options. 
Estimated Completion Time: 20 minutes.
Tip: Before mounting the WN802Tv2 Wireless-N Access Point in a high location, first set 
up and test the WN802Tv2 to verify wireless network connectivity.

a.

Unpack the box and verify the contents.

b. Prepare a computer with Internet access and an Ethernet adapter. If this computer 

is already part of your network, record its TCP/IP configuration settings. 
Configure the computer with a static IP address of 192.168.0.210 and 
255.255.255.0 as the Subnet Mask.

c.

Connect an Ethernet cable from the 
WN802Tv2 to the PC.

d. Securely insert the other end of the cable 

into the WN802Tv2 Ethernet port.

e.

Connect the NETGEAR Switching 
Power Supply from the wireless-N 
access point to an AC power outlet. 
Note: Only connect your wireless-N 
access point using the switching power 
supply provided with the WN802Tv2.

f.

Check the lights on the front of the wireless-N access point:

 

•

Power: The green power light should be 

lit. If the power light is not lit, check the 
connections and check to see if the power 
outlet is controlled by a wall switch that is 
turned off.

•

Ethernet: The Ethernet (LAN) light 

should be lit (amber for 10/100 Mbps and green 
for 1000 Mbps) indicating that a connection 
has been made. If not, make sure the Ethernet 
cable is securely attached at both ends.

•

 WLAN: The blue wireless light should 

be lit and blinking indicating that it is sending a 
signal.

a.

Configure the WN802Tv2 Ethernet port for LAN access.Connect to the 
WN802Tv2 by opening your browser and entering http://192.168.0.233 in the 
address field. 

A login window will display.

b. When prompted, enter 

 for the 

user name and 

 for the 

password, both in lower case letters.
The NETGEAR Wireless-N Access 
Point WN802Tv2 user interface will 
display.

c.

Select Wireless Settings under the 
Setup menu on the left navigation pane and configure your wireless interface for 
wireless access.

d. Then select WEP/WPA Settings under Security and configure the level of data 

encryption security for your network.
See the online help or the online Reference Manual for full instructions.

http://192.168.0.233

e.

Finally, select Basic Settings under the Setup menu on the left navigation pane 
and configure the IP Settings for your network.
Note: If you change the default subnet of the LAN IP address, you will be 
disconnected from the WN802Tv2 Wireless-N Access Point user interface. To 
reconnect, reconfigure your computer with a static IP address within the new 
LAN IP subnet.
Tip: Before you deploy your wireless-N access point, reserve an IP address 
(based on the WN802Tv2’s MAC address) on the DHCP server. That way, you 
can configure the wireless-N access point with a static IP address which you can 
always use to log in to make future configuration changes.

Using a computer with a wireless adapter configured according to the wireless 
settings you just set in the WN802Tv2, establish a wireless connection to the 
WN802Tv2.

Now that you have finished the setup steps, you are ready to deploy the WN802Tv2 in 
your network. If needed, you can now reconfigure the PC you used in step 1 back to its 
original TCP/IP settings.
Warning: To allow for proper ventilation, always install the unit vertically using the 
included stand. Do not lay the unit flat. 
1. Disconnect the WN802Tv2 from the computer and place it where you will deploy it. 

The best location is elevated, such as wall mounted or on the top of a cubicle, at the 
center of your wireless coverage area, and within line of sight of all the mobile 
devices. The WN802Tv2 should be positioned vertically. 

2. Connect an Ethernet cable from your WN802Tv2 wireless-N access point to a LAN 

port on your router, switch, or hub.

3. Connect the power adapter to the wireless-N access point and plug the power adapter 

in to a power outlet. The Power, WLAN and Ethernet lights should light up.

Note: A wall mount kit is included with theWN802Tv2. Instructions for installing the 
brackets and mounting the WN802Tv2are in the online Reference Manual.