Epson 7800p 사용자 설명서
EPSON PowerLite 7800p Projector
5/03
EPSON PowerLite 7800p Projector
-
13
Managing Projectors from a Remote
Computer
Computer
The EasyManagement software lets you monitor and control
projector(s) from a remote computer. These features are
intended for use by network administrators.
projector(s) from a remote computer. These features are
intended for use by network administrators.
❏ Use EMP Monitor to see your projectors’ status, switch
image sources, and control basic settings.
❏ Use EMP NetworkManager to receive e-mail notifications
alerting you to possible problems.
❏ Use a network management utility running SNMP, such as
HP OpenView,
™
to manage your facility’s equipment from
a pre-existing system.
Note: A plug-in is available to allow you to manage your
projectors in HP OpenView. Additionally, other SNMP
management utilities may be available in the future. Check with
EPSON for availability.
projectors in HP OpenView. Additionally, other SNMP
management utilities may be available in the future. Check with
EPSON for availability.
Make sure you have installed the software (included on the
projector’s CD-ROM) on the computer you want to use to
monitor your projectors. (See the User’s Guide for
instructions.)
projector’s CD-ROM) on the computer you want to use to
monitor your projectors. (See the User’s Guide for
instructions.)
Setting Up the Network
Connect each projector you want to monitor to your network
and configure it with an appropriate IP address.
and configure it with an appropriate IP address.
1. Connect the projector to your network using a
commercially available 100baseTX or 10baseT network
cable. Plug the cable into the projector’s Ethernet port.
cable. Plug the cable into the projector’s Ethernet port.
2. Turn on the projector.
3. Press the
Menu
button on the remote control and select
Network
from the
Advanced2
menu.
4. If your network assigns addresses automatically, turn on
DHCP
.
5. If your network does not assign addresses automatically,
turn off
DHCP
and enter the projector’s
IP Address
,
Subnet Mask
, and
Gateway Address
, as needed.
❏ To enter numbers using the remote control, press the
Num
button until it lights, then use the numeric
keypad.
❏ To change the network addresses from the projector’s
control panel, press the right and left arrow buttons to
select the part of the address you want to enter, then
use the up and down arrow buttons to increase or
decrease the numeric value.
select the part of the address you want to enter, then
use the up and down arrow buttons to increase or
decrease the numeric value.
Note: If you’re a network administrator, you can use the
SNMP
option to enter a trap IP address. This lets you receive
trap alerts for the projectors you’re monitoring. If you have
HP OpenView, a plug-in is available to allow you to manage
your projectors in HP OpenView. Check with your dealer or
EPSON.
HP OpenView, a plug-in is available to allow you to manage
your projectors in HP OpenView. Check with your dealer or
EPSON.
To network port
Ethernet port
Br
Brightness Control
ightness Control
High
High
Low
:
Video
Audio
Setting
User's Logo
Advanced1
About
Reset All
Projector ID
Projector ID
Netw
Network
Reset
Reset
Ex
Execute
ecute
: 1
[Menu]: Exit
[ ]: Enter
[ ]: Select
Effect
Advanced2
COM P
COM Port
BNC Sync
BNC Sync Ter
ermination
mination
:
ON
ON
OFF
OFF
:
Set
Set
Set
Set
RS-232C
RS-232C
USB
USB
Auto setup
uto setup
ON
ON
OFF
OFF
:
Select
Network
Network
Num button
Zero
Increase or
decrease
the value
decrease
the value
Select the part of the
address to change
address to change