Milwaukee 2401-22 사용자 설명서

• Keep work area clean and well lit. Cluttered or 

dark areas invite accidents.

spheres, such as in the presence of fl ammable 
liquids, gases or dust. Power tools create sparks 
which may ignite the dust or fumes.

operating a power tool. Distractions can cause 
you to lose control.

modify the plug in any way. Do not use any 
adapter plugs with earthed (grounded) power 
tools. Unmodifi ed plugs and matching outlets will 
reduce risk of electric shock.

surfaces such as pipes, radiators, ranges and 
refrigerators. There is an increased risk of electric 
shock if your body is earthed or grounded.

tions. Water entering a power tool will increase 
the risk of electric shock.

carrying, pulling or unplugging the power tool. 
Keep cord away from heat, oil, sharp edges 
or moving parts. Damaged or entangled cords 
increase the risk of electric shock.

extension cord suitable for outdoor use. Use 
of a cord suitable for outdoor use reduces the risk 
of electric shock.

is unavoidable, use a residual current device 
(RCD) protected supply. Use of an RCD reduces 
the risk of electric shock.

attached to a rotating part of the power tool may 
result in personal injury. 

balance at all times. This enables better control 
of the power tool in unexpected situations.

jewellery. Keep your hair, clothing and gloves 
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts. 

dust extraction and collection facilities, ensure 
these are connected and properly used. Use of 
dust collection can reduce dust-related hazards.

power tool for your application. The correct 
power tool will do the job better and safer at the 
rate for which it was designed.

turn it on and off. Any power tool that cannot be 
controlled with the switch is dangerous and must 
be repaired.

and/or the battery pack from the power tool 
before making any adjustments, changing 
accessories, or storing power tools. Such 
preventive safety measures reduce the risk of 
starting the power tool accidentally.

dren and do not allow persons unfamiliar with 
the power tool or these instructions to operate 
the power tool. Power tools are dangerous in the 
hands of untrained users.

or binding of moving parts, breakage of parts 
and any other condition that may affect the 
power tool’s operation. If damaged, have the 
power tool repaired before use. Many accidents 
are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly 

maintained cutting tools with sharp cutting edges 
are less likely to bind and are easier to control.

etc., in accordance with these instructions, 
taking into account the working conditions and 
the work to be performed. Use of the power tool 
for operations different from those intended could 
result in a hazardous situation.

common sense when operating a power tool. Do 
not use a power tool while you are tired or under 
the infl uence of drugs, alcohol or medication. A 
moment of inattention while operating power tools 
may result in serious personal injury.

wear eye protection. Protective equipment such 
as dust mask, non-skid safety shoes, hard hat, or 
hearing protection used for appropriate conditions 
will reduce personal injuries.

switch is in the off-position before connecting 
to power source and/or battery pack, picking 
up or carrying the tool. Carrying power tools with 
your fi nger on the switch or energising power tools 
that have the switch on invites accidents.

turning the power tool on. A wrench or a key left 

the manufacturer. A charger that is suitable for 
one type of battery pack may create a risk of fi re 
when used with another battery pack.

nated battery packs. Use of any other battery 
packs may create a risk of injury and fi re.

1. Bit holder collar
2. Clutch adjusting ring
3. Fuel Gauge
4. Control Switch
5.  Trigger
6.  LED

1

2

6

5

3

4

Inserting/Removing the Battery
To remove the battery, push in the release buttons 
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of 
the tool. Make sure it latches securely into place.

Volts 

12

0 - 500

1/2”

1/4” 

Fuel Gauge
To determine the amount of charge left in the bat-
tery, pull the trigger. The Fuel Gauge will light up 
for 2-3 seconds. 
To signal the end of charge, 1 light on the fuel gauge 
will fl ash for 2-3 seconds.

Installing Bits
Always remove the battery before inserting or 
removing bits. Select the proper style and size bit 
for the type of screw you are using.
1. To install the bit, press the bit into the socket 

until the collar snaps back and the bit is locked 
into place.

2. To  remove the bit, pull out the collar, then pull 

out the bit.

NOTE: It is not necessary to hold the collar out when 
installing and removing bits. The fi rst time the tool 
is used, it may be necessary to pull out the collar. 

Direct Current

Underwriters Laboratories, Inc.
United States and Canada

No Load Revolutions
per Minute (RPM)

• Wear ear protectors with impact drilling. Expo-

sure to noise can cause hearing loss. 

tool. Loss of control can cause personal injury. 

faces, when performing an operation where the 
fastener may contact hidden wiring or its own 
cord. Fastener contacting a “live” wire may make 
exposed metal parts of the power tool “live” and 
could give the operator an electric shock.

• Maintain labels and nameplates. These carry 

important information. If unreadable or missing, 
contact a MILWAUKEE service facility for a free 
replacement.

• WARNING: Some dust created by power sanding, 

sawing, grinding, drilling, and other construction 
activities contains chemicals known to cause 
cancer, birth defects or other reproductive harm. 
Some examples of these chemicals are:

• lead from lead-based paint
• crystalline silica from bricks and cement and other 

masonry products, and

• arsenic and chromium from chemically-treated 

lumber.

  Your risk from these exposures varies, depending on 

how often you do this type of work. To reduce your ex-
posure to these chemicals: work in a well ventilated 
area, and work with approved safety equipment, 
such as those dust masks that are specially designed 
to fi lter out microscopic particles.

from other metal objects like paper clips, 
coins, keys, nails, screws, or other small metal 
objects that can make a connection from one 
terminal to another. Shorting the battery termi-
nals together may cause burns or a fi re.

ed from the battery; avoid contact. If contact 
accidentally occurs, fl ush with water. If liquid 
contacts eyes, additionally seek medical help. 
Liquid ejected from the battery may cause irritation 
or burns.

repair person using only identical replacement 
parts. This will ensure that the safety of the power 
tool is maintained.