Milwaukee 2401-22 사용자 설명서

This tool provides a quick, convenient means of drill-
ing small holes and installing and removing screws. 
Because of the many screw sizes, types, thread en-
gagements and materials available, it is diffi cult to 
limit the application of this tool by screw size. How-
ever, for applications in wood, a #6 wood screw with 
a full pilot hole is recommended as a practical limit.

Drilling in Wood, Composition Materials and 
Plastic
Always use sharp bits. When using twist drill bits, 
pull the bit out of the hole frequently to clear chips 
from the bit fl utes. To reduce the chance of splinter-
ing, back work with a piece of scrap wood. Select 
low speeds for plastics with a low melting point.

Driving Screws
Drill a pilot hole when driving screws into thick or 
hard materials. Set the clutch adjusting ring to the 
proper position and set the speed to low. Use the 
proper style and size screwdriver bit for the type 
of screw you are using.
With the screwdriver bit in the screw, place the tip 
of the screw on the workpiece and apply fi rm pres-
sure before pressing the foward/reverse switch up. 
Screws can be removed by pressing the foward/
reverse switch down.

Locking the Screwdriver Bit
When the tool is off, the screwdriver bit auto-
matically locks in place allowing you to use the 
screwdriver manually. Do this to tighten screws 
that require more torque than the driver is capable 
of delivering, when confi rming the tightness of a 
screw or when loosening an extremely tight screw.

2
4
6
8

10
12
14

Drill

4
7

10
13
16
19
41

120

Small screws in softwood.

Medium screws in softwood or 
small screws in hardwood.

Large screws in softwoods. Me-
dium screws in hardwood or large 
screws in hardwood with pilot hole.

tool will vibrate for about 5 seconds, the fuel gauge 
will fl ash, and then the tool will turn OFF. To reset, 
release the trigger. 
Under extreme circumstances, the internal tem-
perature of the battery could become too high. 
If this happens, the fuel gauge will fl ash and the 
battery pack will shut off. Let the battery pack cool 
and then continue work.   

Using the Adjustable Clutch 
This tool has an adjustable 
clutch for driving different types 
of screws into different materi-
als. When properly adjusted, 
the clutch will slip at a preset 
torque to prevent driving the 
screw too deep and to prevent 
damage to the screw or tool. 
To adjust the clutch, turn the 
clutch adjusting ring so that 
the desired setting (1-15) lines 
up with the arrow on the motor 
housing, as shown.
The torque specifications shown here are ap-
proximate values obtained with a fully charged 
battery pack.

For forward (clockwise) rotation, push in the control 
switch from the right side of the tool. Check the 
direction of rotation before use.
For reverse (counterclockwise) rotation, push in the 
control switch from the left side of the tool. Check 
direction of rotation before use. 
To lock the trigger, push the control switch to the 
center position. The trigger will not work while the 
control switch is in the center locked position. Always 
lock the trigger or remove the battery pack before 
performing maintenance, changing accessories, 
storing the tool and any time the tool is not in use.

Battery Pack Protection
To protect the battery from damage and extend 
its life, the tool’s intelligent circuit monitors current 
draw, temperature, and voltage drops. 
In extremely high torque, binding, stalling, and short 
circuit situations that cause high current draw, the 

Maintaining Tool 
Keep your tool, battery pack and charger in good re-
pair by adopting a regular maintenance program. 
After six months to one year, depending on use, 
return the tool, battery pack and charger to a 
MILWAUKEE service facility for:
• Lubrication
• Mechanical inspection and cleaning (gears, 

spindles, bearings, housing, etc.)

• Electrical inspection (battery pack, charger, 

motor)

• Testing to assure proper mechanical and 

electrical operation

If the tool does not start or operate at full power 
with a fully charged battery pack, clean the contacts 
on the battery pack. If the tool still does not work 
properly, return the tool, charger and battery pack, 
to a MILWAUKEE service facility for repairs.

Cleaning
Clean dust and debris from charger and tool vents. 
Keep tool handles clean, dry and free of oil or grease. 
Use only mild soap and a damp cloth to clean the 
tool, battery pack and charger since certain cleaning 
agents and solvents are harmful to plastics and other 
insulated parts. Some of these include gasoline, 
turpentine, lacquer thinner, paint thinner, chlorinated 
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use fl ammable or 
combustible solvents around tools.

the battery pack from the charger or tool 
before performing any maintenance. Never 
disassemble the tool, battery pack or charger. 
Contact a MILWAUKEE service facility for ALL 
repairs.

For a complete listing of accessories refer to your 
MILWAUKEE  Electric Tool catalog or go online 
to www.milwaukeetool.com. To obtain a catalog, 
contact your local distributor or service center.

TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase 

date. This warranty card covers any defect in material and workmanship on this 

Power Tool. 

To make this warranty valid, present this warranty card, sealed/stamped by the 

distributor or store where you purchased the product, to the Authorized Service 

Center (ASC). Or, if this card has not been sealed/stamped, present the original 

proof of purchase to the ASC. 

Call toll-free 1 800 832 1949 to fi nd the nearest ASC, for service, parts, acces-

sories or components.   

Take the product to the ASC, along with the warranty card sealed/stamped by the 

distributor or store where you purchased the product, and  there any faulty piece 

or component will be replaced without cost for you. We will cover all freight costs 

relative with this warranty process. 

This warranty is not valid in the following situations: 

a) When the product is used in a different manners from the end-user guide or 

instruction manual. 

b) When the conditions of use are not normal.

c) When the product was modifi ed or repaired by people not authorized by TECH-

TRONIC INDUSTRIES.

Note: If cord set is damaged, it should be replaced by an Authorized Service 

Center to avoid electric risks. 

  

SERVICE AND ATTENTION CENTER

 

Rafael Buelna No.1.

 

Col. Tezozomoc Mexico, Azcapotzalco D.F.

 

Ph. 01 800 832 1949

 

IMPORTED AND COMMERCIALIZED BY:

 

TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.

 

Av. Santa Fe 481 piso 6, Col. Curz Manca. 

 

CP 05349, Cuajimalpa, D.F.

Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) 

- see separate & distinct CORDLESS BATTERY PACK LIMITED WARRANTY 

statements & battery charger and Work Lights*) is warranted to the original 

purchaser only to be free from defects in material and workmanship.  Subject to 

certain exceptions, MILWAUKEE will repair or replace any part on an electric power 

tool which, after examination, is determined by MILWAUKEE to be defective in 

material or workmanship for a period of fi ve (5) years* after the date of purchase 

unless otherwise noted.  Return of the power tool to a MILWAUKEE factory Service 

Center location or MILWAUKEE Authorized Service Station, freight prepaid and 

insured, is required.  A copy of the proof of purchase should be included with the 

return product.  This warranty does not apply to damage that MILWAUKEE deter-

mines to be from repairs made or attempted by anyone other than MILWAUKEE 

authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of 

maintenance, or accidents.

*The warranty period for, Job Site Radios, M12™ Power Port and Trade 

Titan™ Industrial Work Carts is one (1) year from the date of purchase.  The 

warranty period for a LED Work Light and LEDUpgrade Bulb is a limited 

LIFETIME warranty to the original purchaser only, if during normal use the LED 

bulb fails the Work Light or Upgrade Bulb will be replaced free of charge.

*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless 

Battery Packs, Gasoline Driven Portable Power Generators, Hand Tools, Hoist 

– Electric, Lever & Hand Chain, M12™ Heated Jackets, Reconditioned product 

and Test & Measurement products.  There are separate and distinct warranties 

available for these products.

Warranty Registration is not necessary to obtain the applicable warranty on a 

MILWAUKEE power tool product.  The manufacturing date of the product will be 

used to determine the warranty period if no proof of purchase is provided at the 

time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REM-

EDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE 

PURCHASE OF EVERY MILWAUKEE PRODUCT.  IF YOU DO NOT AGREE TO 

THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT.  IN NO 

EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, 

CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, AT-

TORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A 

CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY 

PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF 

PROFITS.  SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION 

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION 

OR EXCLUSION MAY NOT APPLY TO YOU.  THIS WARRANTY IS EXCLUSIVE 

AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.  

TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED 

WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY 

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; 

TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH 

IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE 

EXPRESS WARRANTY AS DESCRIBED ABOVE.  SOME STATES DO NOT 

ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO 

THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES 

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS 

WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the ‘Service Center Search’ in the Parts & Service section of 

MILWAUKEE’s website www.milwaukeetool.com or call 1.800.SAWDUST 

(1.800.729.3878) to locate your nearest MILWAUKEE  factory Service Center 

location. 

NOTE: Because the settings shown in the table are 
only a guide, use a piece of scrap material to test 
the different clutch settings before driving screws 
into the workpiece.

Using Control Switch
The control switch may be set to three positions: 
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when 
the ON/OFF switch is not pressed. Always allow 
the motor to come to a complete stop before using 
the control switch.

Repairs
For repairs, return the tool, battery pack and char-
ger to the nearest service center.