Hoshizaki KM-1301SAH-E 사용자 설명서
20
a) LED Lights and Audible Alarm Safeties
At startup, a 5-second delay occurs while the control board conducts an internal timer
check. A beep occurs when the control switch is moved to the "ICE" position.
The red LED indicates proper control voltage and remains on unless a control voltage
problem occurs. The green LEDs 1 through 4 energize and sequence from initial startup
as listed in the table below. Note that the order of the LEDs from the outer edge of the
control board is 1, 4, 3, 2. For details, see "II.B. Sequence of Operation."
check. A beep occurs when the control switch is moved to the "ICE" position.
The red LED indicates proper control voltage and remains on unless a control voltage
problem occurs. The green LEDs 1 through 4 energize and sequence from initial startup
as listed in the table below. Note that the order of the LEDs from the outer edge of the
control board is 1, 4, 3, 2. For details, see "II.B. Sequence of Operation."
Sequence Step
LED
Energized
Components
Time LEDs are On
Min.
Max.
Avg.
1-Minute Fill Cycle
4
WV
1 minute
Harvest Cycle
1, 4, 2
Comp, FMR, WV,
HGV
HGV
2 minutes
20 minutes
3 to 5 minutes
Harvest Pump Timer 1, 3, 2
Comp, FMR, PM,
HGV
HGV
0 seconds
50 seconds harvest pump timer
setting
Freeze Cycle
1
Comp, FM/FMR,
PM, LLV
PM, LLV
5 minutes
freeze timer
setting
setting
30 to 35 minutes
Pump-Out Cycle
1, 4*, 3, 2 Comp, FMR, WV*,
PM, HGV
10 seconds
20 seconds *pump-out timer
setting
The built-in safeties shut down the unit and have alarms as listed below.
No. of Beeps
(every 3 sec.)
Type of Alarm
Notes
1
High Evaporator Temp.
(temperature > 127°F (53°C))
(temperature > 127°F (53°C))
Check for harvest problem (stuck HGV or relay), hot
water entering unit, stuck HM, or shorted thermistor.
water entering unit, stuck HM, or shorted thermistor.
2
Harvest Backup Timer
(harvest > 20 min. for two cycles
in a row)
(harvest > 20 min. for two cycles
in a row)
Check for open thermistor, HGV not opening, TXV or
LLV leaking by, low charge, inefficient Comp., or WRV
leaking by.
LLV leaking by, low charge, inefficient Comp., or WRV
leaking by.
3
Freeze Timer
(freeze > freeze timer setting for
two cycles in a row)
Timer is factory set using S4 dip
switch 9 & 10
(freeze > freeze timer setting for
two cycles in a row)
Timer is factory set using S4 dip
switch 9 & 10
Check for F/S stuck closed (up), WV leaking by, HGV
leaking by, PM not pumping, TXV not feeding properly,
LLV not opening, low charge, HM not bypassing, or
inefficient Comp.
leaking by, PM not pumping, TXV not feeding properly,
LLV not opening, low charge, HM not bypassing, or
inefficient Comp.
To reset the above safeties, press the "ALARM RESET" button with the power supply on.
6
Low Voltage
(92Vac±5% or less)
(92Vac±5% or less)
Red LED turns off if voltage protection operates.
The control voltage safeties automatically reset when
voltage is corrected.
The control voltage safeties automatically reset when
voltage is corrected.
7
High Voltage
(147Vac±5% or more)
(147Vac±5% or more)
Legend:
Comp–compressor; FM–fan motor; FMR–fan motor-remote; F/S–float switch;
HGV–hot gas valve; HM–headmaster (C.P.R.); LLV–liquid line valve; PM–pump
motor;
motor;
TXV–thermostatic expansion valve; WRV–water regulating valve; WV–inlet
water valve