Netgear FS726TP 하드웨어 매뉴얼
Page 10 of 19
SFP GBIC Module
The module bays accommodate standard SFP GBIC modules, such as the AGM731F or AGM732F from NETGEAR, allowing you to have fiber
connections on your network. The module bays are combo ports, sharing a connection with an RJ-45 port. Being a combo port, only one type of
connection can be active at any given time. For example, both copper and fiber port cannot be used at the same time. If both connectors are
plugged in at the same time, the fiber port will be active.
The SFP GBIC bay accommodates a standard SFP GBIC module.
connections on your network. The module bays are combo ports, sharing a connection with an RJ-45 port. Being a combo port, only one type of
connection can be active at any given time. For example, both copper and fiber port cannot be used at the same time. If both connectors are
plugged in at the same time, the fiber port will be active.
The SFP GBIC bay accommodates a standard SFP GBIC module.
LED Descriptions
The front panel of the NETGEAR ProSafe FS726TP Smart Switch with PoE has LEDs that provide a quick and accurate display of link, port speed,
and activity. Table 2-1 summarizes the LEDs on the switch.
and activity. Table 2-1 summarizes the LEDs on the switch.
Table 2-1. Front Panel LEDs:
Port Group
Feature
Detailed Description
System Power
LED
MAX POE
Solid Green –Power is supplied to the switch & operating normally
Off – Power is Disconnected.
Solid Yellow – Indicates less than 7W of PoE power is available
Off – Power is Disconnected.
Solid Yellow – Indicates less than 7W of PoE power is available
Blinking Yellow –Indicates the PoE MAX LED was active in the previous
two minutes
two minutes
.
Off –There is at least 7W of PoE power available for another device
10/100M Ports
Link/ACT
100M
z
Solid Green – A valid 10/100Mbps link is established on the port.
z
Blinking Green – Packets transmission or reception is occurring on
the port at 100Mbps.
z
OFF –No 10/100Mbps link is established on the port.
z
Solid Green – A valid 100Mbps link is established on the port.
z
OFF –No 10Mbps link is established on the port.
PoE Ports (ports 1 to 12)
POE / POE fault
z
Solid Green – The PoE powered device (PD) is connected and the
port is supplying power successfully.
z
z
Solid Yellow – Indicates one of the following failures resulted in
stopping power to that port:
· Short circuit on PoE power circuit
· PoE power demand exceeds power available
· PoE current exceeds PD's classification
· Out of proper voltage band (44 ~ 57 VDC)
z
· Short circuit on PoE power circuit
· PoE power demand exceeds power available
· PoE current exceeds PD's classification
· Out of proper voltage band (44 ~ 57 VDC)
z
OFF –No PoE powered device (PD) connected.
10/100/1000M Ports
Link/ACT
100/1000M
z
Solid Green – A valid 10/100/1000Mbps link is established on the
port.
z
Blinking Green – Packets transmission or reception is occurring on
the port at 10/100/1000Mbps.
z
OFF –No 10/100/1000Mbps link is established on the port.
z
Solid Green –A valid 1000Mbps link is established on the port.
z
Solid Yellow – A valid 100Mbps link is established on the port.
z
OFF –No 100/1000Mbps link is established on the port.
SFP (Mini GBIC)
Link
z
Solid Green – A valid link is established on the port.
z
OFF –No link is established on the port.