ZyXEL 793H 사용자 가이드
Chapter 23 WAN Setup
P-793H User’s Guide
251
23.1.1 2wire-2line Service Mode
From the main menu, enter 2 to open menu 2, then select 2wire-2line in the Service Mode
field to see the screen as shown below.
field to see the screen as shown below.
Figure 143 Menu 2: 2wire-2line Service Mode
The following table describes the fields in this screen.
Menu 2 - WAN Setup
Service Mode= 2wire-2line
Service Type= N/A
Rate Adaption= Disable Rate Adaption= Enable
Transfer Max Rate(Kbps)= 4480 Transfer Max Rate(Kbps)= 5696
Transfer Min Rate(Kbps)= 4480 Transfer Min Rate(Kbps)= 3200
Standard Mode= ANSI(ANNEX_A) Standard Mode= ANSI(ANNEX_A)
Wan Backup Setup:
Check Mechanism = DSL Link
Check WAN IP Address1 = 0.0.0.0
Check WAN IP Address2 = 0.0.0.0
Check WAN IP Address3 = 0.0.0.0
KeepAlive Fail Tolerance = 0
Recovery Interval(sec) = 0
ICMP Timeout(sec) = 0
Traffic Redirect = No
Dial Backup = No
Service Type= N/A
Rate Adaption= Disable Rate Adaption= Enable
Transfer Max Rate(Kbps)= 4480 Transfer Max Rate(Kbps)= 5696
Transfer Min Rate(Kbps)= 4480 Transfer Min Rate(Kbps)= 3200
Standard Mode= ANSI(ANNEX_A) Standard Mode= ANSI(ANNEX_A)
Wan Backup Setup:
Check Mechanism = DSL Link
Check WAN IP Address1 = 0.0.0.0
Check WAN IP Address2 = 0.0.0.0
Check WAN IP Address3 = 0.0.0.0
KeepAlive Fail Tolerance = 0
Recovery Interval(sec) = 0
ICMP Timeout(sec) = 0
Traffic Redirect = No
Dial Backup = No
Table 95 Menu 2: 2wire-2line Service Mode
FIELD
DESCRIPTION
Service Mode
Press [SPACE BAR] to select 2wire-2line service mode. This means you are
establishing a point-to-2point connection. See
for more
background information. In 2wire-2line mode, the maximum data rate is up to 5.69
Mbps for each DSL connection.
Service Type
The ZyXEL Device automatically acts as a server in 2wire-2line mode.
Rate Adaption
The field on the left refers to DSL 1 connection and the field on the right refers to
DSL 2 connection. Press [SPACE BAR] to let the ZyXEL Device adjust the speed of
its connection to that of the other device.
Transfer Max
Rate(Kbps)
The field on the left refers to DSL 1 connection and the field on the right refers to
DSL 2 connection. Press [SPACE BAR] to set the maximum rate at which the ZyXEL
Device sends and receives information. If you enable Rate Adaption, the ZyXEL
Device adjusts to the speed of the other device and may exceed this rate.
Transfer Min
Rate(Kbps)
The field on the left refers to DSL 1 connection and the field on the right refers to
DSL 2 connection. Press [SPACE BAR] to set the minimum rate at which the ZyXEL
Device sends and receives information. If you enable Rate Adaption, the ZyXEL
Device adjusts to the speed of the other device and may transfer information at less
than this rate.
Standard Mode
The field on the left refers to DSL 1 connection and the field on the right refers to
DSL 2 connection. Press [SPACE BAR] to select the operational mode the ZyXEL
Device uses in the DSL connection.
Wan Backup
Setup