KitchenAid kdrp467kss 설치 설명서
Before you start...
It is the customer’s responsibility:
• To contact a qualified electrical installer.
• To assure that electrical installation is
• To assure that electrical installation is
adequate and in conformance with
National Electrical Code, ANSI/NFPA
70 — latest edition**, or CSA Standard,
C22.1 Canadian Electrical Code, Part 1
— latest edition*, and all local codes
and ordinances.
National Electrical Code, ANSI/NFPA
70 — latest edition**, or CSA Standard,
C22.1 Canadian Electrical Code, Part 1
— latest edition*, and all local codes
and ordinances.
Cabinet opening dimensions shown
must be used. Given dimensions are
minimum clearances.
Note: Some cabinet and building
materials are not designed to withstand
the heat produced by the oven for baking
and self-cleaning. Check with your builder
or cabinet supplier to make sure that the
materials used will not discolor,
delaminate or sustain other damage.
The backguard included with the range
must be installed when a standard 24"
(61 cm) deep base cabinet is used and
there is zero clearance between the back
edge of range and combustible rear wall.
For island installations or other
installations with more than 1" (25.4 mm)
clearance to the back wall, use the
optional stainless steel island trim,
included with the range, to cover the
backguard mounting flanges.
All openings in the wall or floor where the
range is to be installed must be sealed.
It is recommended that a range hood be
installed above this range.
must be used. Given dimensions are
minimum clearances.
Note: Some cabinet and building
materials are not designed to withstand
the heat produced by the oven for baking
and self-cleaning. Check with your builder
or cabinet supplier to make sure that the
materials used will not discolor,
delaminate or sustain other damage.
The backguard included with the range
must be installed when a standard 24"
(61 cm) deep base cabinet is used and
there is zero clearance between the back
edge of range and combustible rear wall.
For island installations or other
installations with more than 1" (25.4 mm)
clearance to the back wall, use the
optional stainless steel island trim,
included with the range, to cover the
backguard mounting flanges.
All openings in the wall or floor where the
range is to be installed must be sealed.
It is recommended that a range hood be
installed above this range.
Important: Observe all governing
codes and ordinances.
codes and ordinances.
Note: The range cooktop is
manufactured for use with Natural gas.
To convert to L.P./Propane gas, see the
Gas Conversion instructions provided in
literature package.
manufactured for use with Natural gas.
To convert to L.P./Propane gas, see the
Gas Conversion instructions provided in
literature package.
Proper gas and electrical supply
connections
connections
must be available. See “Gas
supply requirements,” Page 4 and
“Electrical requirements,” Page 5.
“Electrical requirements,” Page 5.
Important: Obseve all governing codes
and ordinances.
and ordinances.
Do not obstruct flow of combustion
and ventilation air.
and ventilation air.
Proper installation is your responsibility.
Have a qualified technician install this
range. Make sure you have everything
necessary for correct installation. It is the
installer's responsibility to comply with the
installation clearances specified on the
gas information label. The gas information
label and model/serial rating plate are
located on the surface below the control
panel.
Have a qualified technician install this
range. Make sure you have everything
necessary for correct installation. It is the
installer's responsibility to comply with the
installation clearances specified on the
gas information label. The gas information
label and model/serial rating plate are
located on the surface below the control
panel.
This installation must conform with all
local codes and ordinances. In the
absence of local codes, installation must
conform with American National
Standard, National Fuel Gas Code ANSI
Z223.1 — latest edition* or CAN/CGA —
B149 — latest edition* installation codes.
local codes and ordinances. In the
absence of local codes, installation must
conform with American National
Standard, National Fuel Gas Code ANSI
Z223.1 — latest edition* or CAN/CGA —
B149 — latest edition* installation codes.
WARNING: If the
information in this manual
is not followed exactly, a
fire or explosion may result
causing property damage,
personal injury or death.
information in this manual
is not followed exactly, a
fire or explosion may result
causing property damage,
personal injury or death.
— Do not store or use
gasoline or other
flammable vapors and
liquids in the vicinity of
this or any other
appliance.
flammable vapors and
liquids in the vicinity of
this or any other
appliance.
— WHAT TO DO IF YOU
SMELL GAS
• Do not try to light any
appliance.
• Do not touch any
electrical switch.
• Do not use any phone in
your building.
• Immediately call your
gas supplier from a
neighbor’s phone. Follow
the gas supplier’s
instructions.
neighbor’s phone. Follow
the gas supplier’s
instructions.
• If you cannot reach your
gas supplier, call the fire
department.
department.
— Installation and service
must be performed by a
qualified installer, service
agency or the gas
supplier.
qualified installer, service
agency or the gas
supplier.
2
Copies of the standards listed may be obtained
from:
from:
* CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
Cleveland, Ohio 44131-5575
** National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269
Quincy, Massachusetts 02269
You can be killed or seriously
injured if you don’t follow
instructions.
injured if you don’t follow
instructions.
DANGER
Your safety and the safety of
others are very important.
others are very important.
We have provided many important
safety messages in this manual and
on your appliance. Always read and
obey all safety messages.
safety messages in this manual and
on your appliance. Always read and
obey all safety messages.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
You can be killed or seriously
injured if you don’t immediately
follow instructions.
injured if you don’t immediately
follow instructions.
WARNING
This is the safety alert
symbol.
This symbol alerts you to
symbol.
This symbol alerts you to
potential hazards that can kill or hurt
you and others.
All safety messages will follow the
safety alert symbol and either the
word “DANGER” or “WARNING”.
These words mean:
you and others.
All safety messages will follow the
safety alert symbol and either the
word “DANGER” or “WARNING”.
These words mean: