Baumatic bgt1 사용자 설명서
14
4.5 - FUNCTIONING CHECK
To check the machine functioning, just turn the “start” regulator knob clockwise
(placing yourself in front of the knob), and starting from the minimum, observe if
the pilot lamp turns on .
When the pilot lamp is on, it means that the machine is functioning.
To check the machine functioning, just turn the “start” regulator knob clockwise
(placing yourself in front of the knob), and starting from the minimum, observe if
the pilot lamp turns on .
When the pilot lamp is on, it means that the machine is functioning.
CHAP. 5 - USE OF THE MACHINE
5.1 - CONTROLS ON THE GRILLERS
The controls are placed on the machine has shown in the figure below.
The controls are placed on the machine has shown in the figure below.
5.2 - CONTROLS ON THE TOASTERS
The controls are placed on the machine as shown in the figure below.
The controls are placed on the machine as shown in the figure below.
FIG. n°10 - Controls position on the grillers
FIG. n°11 - Controls position on the toasters
1
2
1. Thermostat
2. Pilot lamp, it indicates that the resistors are on.
2. Pilot lamp, it indicates that the resistors are on.
1. Timer, for cooking time regulation.
5.3 - FIRST USE OF THE MACHINE
When the machine is delivered, the steel surfaces are protected with a nylon
anti-scratch film. This film has to be removed accurately before starting the
machine and pay attention to remove eventual residuals of glue.
To perform this operation, do not use sharpening tools, inflammable or abrasive
substances.
The insulating materials used during the manufacturing and the residuals of
grease due to the mechanical installation of single parts, heat and produce smoke,
for this reason, it is necessary to start the machine outside, putting it at the
maximum for 15-20 minutes.
WARNING
When the machine is delivered, the steel surfaces are protected with a nylon
anti-scratch film. This film has to be removed accurately before starting the
machine and pay attention to remove eventual residuals of glue.
To perform this operation, do not use sharpening tools, inflammable or abrasive
substances.
The insulating materials used during the manufacturing and the residuals of
grease due to the mechanical installation of single parts, heat and produce smoke,
for this reason, it is necessary to start the machine outside, putting it at the
maximum for 15-20 minutes.
WARNING
: When you place the product on the grid to cook it, this must be hot,
so pay attention to residual risks due to burning dangers.
To load the product follow this procedure:
so pay attention to residual risks due to burning dangers.
To load the product follow this procedure:
1
3
CHAP. 5 - USE OF THE MACHINE
pag. 14
5.1
- CONTROLS
5.2
- FIRST USE OF THE MACHINE
CHAP. 6 - GENERAL CLEANING
pag. 15
6.1
- INTRODUCTION
CHAP. 7 - MAINTENANCE
pag. 16
7.1
- GENERAL FEATURES
7.2
- POWER SUPPLY CORD
7.3
- QUARTZ TUBES (TOASTER)
CHAP.8 - DISPOSAL OF THE MACHINE
pag. 16
8.1 - PUTTING THE MACHINE OUT OF SERVICE
8.2 - DISPOSAL OF THE MACHINE
8.2 - DISPOSAL OF THE MACHINE
LIST OF THE FIGURES
FIG. n°1 - General view of the machine
pag.
6
FIG. n°2 - Overall dimensions
pag.
6
FIG. n°3 - Package description
pag.
8
FIG. n°4 - Rating plate - serial number
pag.
9
FIG. n°5 - Electric circuit diagram of the GRILLERS: PDM/R/L/X; pag.
10
P2L
FIG. n°6 - Electric circuit diagram of the GRILLERS: TOP R/L/X
pag.
11
FIG. n°7 - Electric circuit diagram of the GRILLERS: CORT R/L/X pag.
12
CORT CRÊPES; ELIO R/L; P1L
FIG. n°8 - Electric circuit diagram of the TOASTERS: 4Q / 6Q
pag.
13
FIG. n°9 - Electric circuit diagram of the TOASTERS: 12Q
pag.
13
FIG. n°10 - Position of controls on the GRILLERS
pag.
14
FIG. n°11 - Position of controls on the TOASTERS
pag.
14
FIG. n°12 - Correct position to use the machine
pag. 15