Cisco Cisco Token Ring Port Adapters 설치 가이드
Corporate Headquarters:
Copyright © 2002. Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
PA-1C-P Parallel Channel Port Adapter
Installation and Configuration
Installation and Configuration
Product Number: PA-1C-P(=)
This document contains instructions for installing and configuring the Parallel Channel Port Adapter
(PCPA), which is used in the Cisco 7200 series routers.
(PCPA), which is used in the Cisco 7200 series routers.
For complete descriptions of interface configuration commands and the configuration options available
for Cisco 7200 series interfaces that support the PCPA functionality, refer to the appropriate software
configuration publication listed in the “If You Need More Information” section on page 2.
for Cisco 7200 series interfaces that support the PCPA functionality, refer to the appropriate software
configuration publication listed in the “If You Need More Information” section on page 2.
Note
Cisco IOS Release 11.3(7)T or later or Release 12.0(1) or later supports the PCPA. When
ordered as a spare, the PCPA microcode is available via Cisco.com. When ordered as part
of a new system, the PCPA microcode is available on Flash memory cards or SanDisk
memory devices (which also include the Cisco IOS software release compatible with the
microcode version) and via Cisco.com. When the PCPA is shipped with a new system, there
is a default setting in the Cisco IOS software that points to the PCPA microcode with which
it has been virtually bundled (separately bundled and preloaded onto the Flash memory
card or SanDisk memory device along with the compatible Cisco IOS software). The
Cisco IOS software loads the PCPA microcode image onto the PCPA when the router boots
and when a PCPA is inserted into a router that has already been booted.
ordered as a spare, the PCPA microcode is available via Cisco.com. When ordered as part
of a new system, the PCPA microcode is available on Flash memory cards or SanDisk
memory devices (which also include the Cisco IOS software release compatible with the
microcode version) and via Cisco.com. When the PCPA is shipped with a new system, there
is a default setting in the Cisco IOS software that points to the PCPA microcode with which
it has been virtually bundled (separately bundled and preloaded onto the Flash memory
card or SanDisk memory device along with the compatible Cisco IOS software). The
Cisco IOS software loads the PCPA microcode image onto the PCPA when the router boots
and when a PCPA is inserted into a router that has already been booted.
We recommend that you use the version of the PCPA microcode that is virtually bundled
with your Cisco IOS software. If you choose not to, you must then copy a microcode image
onto the router Flash memory card or SanDisk memory device and use the microcode
router configuration command to instruct the Cisco IOS software to use this microcode
image instead of the microcode image virtually bundled with your version of the Cisco IOS
software.
with your Cisco IOS software. If you choose not to, you must then copy a microcode image
onto the router Flash memory card or SanDisk memory device and use the microcode
router configuration command to instruct the Cisco IOS software to use this microcode
image instead of the microcode image virtually bundled with your version of the Cisco IOS
software.
For instructions on placing PCPA microcode on the router Flash memory card, see the
“Copying to the Flash Memory Card on a Cisco 7200 Series Router” section on page 33.
For instructions on placing PCPA microcode on the SanDisk memory device, see the
“Using SanDisk Devices” section on page 36.
“Copying to the Flash Memory Card on a Cisco 7200 Series Router” section on page 33.
For instructions on placing PCPA microcode on the SanDisk memory device, see the
“Using SanDisk Devices” section on page 36.
For instructions on configuring Cisco IOS software to use a PCPA image from the router