Cisco Cisco 4-Port OC-3c STM-1c ATM Shared Port Adapter 기술 매뉴얼
Router(config-controller)# au-4 1 tug-3 1
Router(config-ctrlr-tug3)#
no tug-2 1 e1 1 loopback local
If interface doesn’t come up then try to do a shut-no-shut on the TUG as shown below:
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#controller SONET 3/0/0
Router(config-controller)# au-4 1 tug-3 1
Router(config-ctrlr-tug3)#
tug-2 1 e1 1 shutdown
Router(config-ctrlr-tug3)# no tug-2 1 e1 1 shutdown
5.
If interface still doesn’t come up then try to reconfigure the TUGS as shown below:
Router#
show running-config | sec controller SONET 3/0/0
controller SONET 3/0/0
framing sdh
clock source line
aug mapping au-4
!
au-4 1 tug-3 1
mode c-12
tug-2 1 e1 1 channel-group 0 timeslots 1-8
tug-2 1 e1 1 channel-group 1 timeslots 13-14
tug-2 1 e1 1 channel-group 2 timeslots 9-12
<Output suppressed>
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#controller SONET 3/0/0
Router(config-controller)# au-4 1 tug-3 1
Router(config-ctrlr-tug3)#
no tug-2 1 e1 1
Router(config-ctrlr-tug3)# tug-2 1 e1 1 channel-group 0 timeslots 1-8
Router(config-ctrlr-tug3)# tug-2 1 e1 1 channel-group 1 timeslots 13-14
Router(config-ctrlr-tug3)# tug-2 1 e1 1 channel-group 2 timeslots 9-12
Note: Ensure to
configure all channel-groups for the TUG that you reconfigured.
6.
If all the interfaces are down under the controller, then check by giving soft loop to the
complete SONET controller.
complete SONET controller.
Router#
show ip interface brief
Interface IP-Address OK? Method Status Protocol
Serial3/0/0.1/1/1/1:0 192.168.1.1 YES NVRAM down down
Serial3/0/0.1/1/1/1:1 192.168.2.1 YES NVRAM down down
Serial3/0/0.1/1/1/1:2 192.168.3.1 YES NVRAM down down
Serial3/0/0.1/1/1/1:3 192.168.4.1 YES NVRAM down down
Serial3/0/0.1/1/1/1:4 192.168.5.1 YES NVRAM down down
Serial3/0/0.1/1/1/1:5 192.168.6.1 YES NVRAM down down
Serial3/0/0.1/1/1/2:0 192.168.7.1 YES NVRAM down down
Serial3/0/0.1/1/1/2:1 192.168.8.1 YES NVRAM down down
Serial3/0/0.1/1/1/2:2 192.168.9.1 YES NVRAM down down
Serial3/0/0.1/1/1/2:3 192.168.10.1 YES NVRAM down down
Serial3/0/0.1/1/1/3:0 192.168.11.1 YES NVRAM down down
Serial3/0/0.1/1/1/3:1 192.168.12.1 YES NVRAM down down
Serial3/0/0.1/1/1/3:2 192.168.13.1 YES NVRAM down down
Serial3/0/0.1/1/2/1:0 192.168.14.1 YES NVRAM down down
Serial3/0/0.1/1/2/2:0 192.168.15.1 YES NVRAM down down
Serial3/0/0.1/1/2/3:0 192.168.16.1 YES NVRAM down down
Router(config)#
controller sonet 3/0/0
Router(config-controller)#
loopback local
If the controller comes up (as show below) then issue is again not with the local card and
troubleshooting needs to be done on the remote end.
troubleshooting needs to be done on the remote end.
7.