PEHA Aura D 20.455.21 FU-BLS JR 사용자 설명서
제품 코드
D 20.455.21 FU-BLS JR
Easyclick radio system
Easyclick baldachin dimmer receiver Plus, 1 channel
The Easyclick baldachin receiver switches and dims lights according to various selectable
451 FU-BEP DAB
363913
functions and parameters.
This dimmer is controlled by trailing-edge phase cut; it is used with low-voltage halogen
lamps with electronic transformer, filament lamps, high-voltage halogen lamps, and other
ohmic loads.
Standard function: ON/OFF/dimming, 2-pushbutton function with memory.
Selectable functions: ON/OFF/dimming, 2-pushbutton function without memory,
ON/OFF defined by 2-pushbutton function, dim up/dim down defined by 2-pushbutton
function, ON/OFF/dimming, 1-pushbutton function with memory, staircase lighting
function with settable switching off delay and advance off warning, 4 light scenarios,
all can be saved and activated at the touch of a button (one lighting scenario per push-
button). One function can be specified individually per transmitter once it has been trained.
Connection data: 60 (minimum ) to 250 (maximum) watts
Height of casing 27 mm, with screw hook hole, IP 20, with connection wiring,
230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.
This dimmer is controlled by trailing-edge phase cut; it is used with low-voltage halogen
lamps with electronic transformer, filament lamps, high-voltage halogen lamps, and other
ohmic loads.
Standard function: ON/OFF/dimming, 2-pushbutton function with memory.
Selectable functions: ON/OFF/dimming, 2-pushbutton function without memory,
ON/OFF defined by 2-pushbutton function, dim up/dim down defined by 2-pushbutton
function, ON/OFF/dimming, 1-pushbutton function with memory, staircase lighting
function with settable switching off delay and advance off warning, 4 light scenarios,
all can be saved and activated at the touch of a button (one lighting scenario per push-
button). One function can be specified individually per transmitter once it has been trained.
Connection data: 60 (minimum ) to 250 (maximum) watts
Height of casing 27 mm, with screw hook hole, IP 20, with connection wiring,
230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.
Button fixture, 1 gang, for Easyclick in-wall receiver with support plate
451 FU-EP UP o.A. and 451 FU-EP DAB UP o.A.
451 FU-EP UP o.A. and 451 FU-EP DAB UP o.A.
AURA pure white
20.420.02
119113
anthracite
20.420.21
132413
aluminum
20.420.70
158713
Note: The button fixtures can also be delivered in the STANDARD, DIALOG and
NOVA design.
Button fixture, 2 gang, for Easyclick in-wall receiver with support plate,
with lable UP/DOWN 452 FU-EP JR UP o.A.
with lable UP/DOWN 452 FU-EP JR UP o.A.
AURA pure white
20.425.02 JR
132013
anthracite
20.425.21 JR
132113
aluminum
20.425.70 JR
132813
Note: The button fixtures can also be delivered in the STANDARD, DIALOG and
NOVA design.
Easyclick 2-level repeater in plug casing (SCHUKO)
The Easyclick repeater increases the range and therefore the working area between
pure white
453 FU-RP ST
349013
Easyclick transmitters and receivers.
In 1-level operation the radio signal of the transmitter is received, verified and sent to the
respective receiver with the maximum transmission power.
In the 2-level operation a radio signal can be sent over an even greater distance using
maximum two repeaters to the respective receivers. A configuration is not necessary for
the repeater (e.g. programming the transmitter).
The implementation is done with the simple plugging in to a SCHUKO plug.
The 1-level operation of the repeater is the standard factory settings and the repeater can
simply be changed to the 2-level operation depending on the project.
IP 20, 230 V, 50 Hz, neutral conductor required.
In 1-level operation the radio signal of the transmitter is received, verified and sent to the
respective receiver with the maximum transmission power.
In the 2-level operation a radio signal can be sent over an even greater distance using
maximum two repeaters to the respective receivers. A configuration is not necessary for
the repeater (e.g. programming the transmitter).
The implementation is done with the simple plugging in to a SCHUKO plug.
The 1-level operation of the repeater is the standard factory settings and the repeater can
simply be changed to the 2-level operation depending on the project.
IP 20, 230 V, 50 Hz, neutral conductor required.
Easyclick 2-level flush-mounted repeater
The Easyclick repeater increases the range and therefore the working area between
453 FU-RPP o.T.
379513
Easyclick transmitters and receivers.
In 1-level operation the radio signal of the transmitter is received, verified and sent to the
respective receiver with the maximum transmission power.
In the 2-level operation a radio signal can be sent over an even greater distance using
maximum two repeaters to the respective receivers. A configuration is not necessary for
the repeater (e.g. programming the transmitter).
The implementation is done with the simple plugging in to a 230 V,
e.g. a 1960s switch plug.
The 1-level operation of the repeater is the standard factory settings and the repeater can
simply be changed to the 2-level operation depending on the project.
IP 20, 230 V, 50 Hz, neutral conductor required.
In 1-level operation the radio signal of the transmitter is received, verified and sent to the
respective receiver with the maximum transmission power.
In the 2-level operation a radio signal can be sent over an even greater distance using
maximum two repeaters to the respective receivers. A configuration is not necessary for
the repeater (e.g. programming the transmitter).
The implementation is done with the simple plugging in to a 230 V,
e.g. a 1960s switch plug.
The 1-level operation of the repeater is the standard factory settings and the repeater can
simply be changed to the 2-level operation depending on the project.
IP 20, 230 V, 50 Hz, neutral conductor required.
Easyclick window contact
This door/window contact monitors the status of doors and windows, it does not need a
450 FU FK
367113
battery, it is operated by Easyclick radio signals via the Easyclick Plus receiver.
The Easyclick window contact is wireless and completely maintenance-free, it incorporates
an internal solar-powered energy store. It continues to operate through dark spells lasting
several days. Signal transmission is immediate, as soon as a window opens or closes, it is
triggered by a window magnet. The window contact can be fitted to all the usual frame
profiles. Thanks to its wireless radio transmission the window contact is ideal for installing
in existing buildings in order to improve security. It is compatible with the Easyclick Plus
receiver and the PHC system. Colour similar to RAL 9003, protection IP 40,
dimensions of the window contact: 110 x 19 x 15 mm (L x W x H),
dimensions of the magnet: 23 x 14 x 6 mm (L x W xH).
The Easyclick window contact is wireless and completely maintenance-free, it incorporates
an internal solar-powered energy store. It continues to operate through dark spells lasting
several days. Signal transmission is immediate, as soon as a window opens or closes, it is
triggered by a window magnet. The window contact can be fitted to all the usual frame
profiles. Thanks to its wireless radio transmission the window contact is ideal for installing
in existing buildings in order to improve security. It is compatible with the Easyclick Plus
receiver and the PHC system. Colour similar to RAL 9003, protection IP 40,
dimensions of the window contact: 110 x 19 x 15 mm (L x W x H),
dimensions of the magnet: 23 x 14 x 6 mm (L x W xH).
Article designation
Colour
Article No.
Code No.