Cisco Cisco FirePOWER Appliance 7125 설치 가이드
Quick Start Guide - 7000 Series Devices
7000 SERIES
INSTALLING
2014-5.3-3
Page 6 of 8
Installing the Device
To install the device:
Mount the device in your rack using the mounting kit and its supplied instructions.
1.
Connect to the device using either a keyboard and monitor or an Ethernet connection.
2.
If you are using a keyboard and monitor to set up the device, use an Ethernet cable now to connect the management interface to a
•
protected network segment.
If you plan to perform the initial setup process by connecting a computer directly to the device’s physical management interface,
If you plan to perform the initial setup process by connecting a computer directly to the device’s physical management interface,
•
you will connect the management interface to the protected network when you finish setup.
Connect the sensing interfaces to the network segments you want to analyze using the appropriate cables for your interfaces: See
3.
Connecting the Sensing Interfaces on page 4.
Attach the power cord to the device and plug into a power source.
4.
If your device has redundant power supplies, attach power cords to both power supplies and plug them into separate power sources.
Turn on the device.
5.
If you are using a keyboard and monitor to set up the device, continue with Configuring Network Settings Using a Script in the
•
Sourcefire 3D System Installation Guide
.
If you are using a direct Ethernet connection to set up the device, confirm that the link LED is on for both the network interface on
•
the local computer and the management interface on the device. If the management interface and network interface LEDs are not
lit, try using a crossover cable. For more information, see Cabling Inline Deployments on Copper Interfaces in the
lit, try using a crossover cable. For more information, see Cabling Inline Deployments on Copper Interfaces in the
Sourcefire 3D
System Installation Guide
.
After you have configured network settings, make sure the device is connected to the protected management network with an Ethernet
6.
cable and continue the initial setup with Initial Setup: Devices in the
Sourcefire 3D System Installation Guide
.
You can find detailed information on additional configuration options (such as testing an inline bypass configuration, reconfiguring your
console output, and so on) in the
console output, and so on) in the
Sourcefire 3D System Installation Guide
.
The Sourcefire 3D System is delivered on different hardware platforms that you can rack-mount. When you install a device,
make sure that you can access the device’s console for initial setup.
make sure that you can access the device’s console for initial setup.
You can access the console for initial setup using a keyboard and monitor with KVM, or using an Ethernet connection to the
management interface.
management interface.
Keyboard and Monitor/KVM
You can connect a USB keyboard and VGA monitor to any Sourcefire device, which is useful for rack-mounted devices
connected to a keyboard, video, and mouse (KVM) switch.
connected to a keyboard, video, and mouse (KVM) switch.
IMPORTANT! Do not use a KVM switch with USB mass storage to access the device because the device may attempt to
use the mass storage device as a boot device.
use the mass storage device as a boot device.
Ethernet Connection to Management Interface
Configure a local computer, which must not be connected to the internet, with the following network settings:
IP address:
•
192.168.45.2
netmask:
•
255.255.255.0
default gateway:
•
192.168.45.1
Using an Ethernet cable, connect the network interface on the local computer to the management interface on the
device. To interact with the device, use terminal emulation software such as HyperTerminal or XModem with the
following software settings:
device. To interact with the device, use terminal emulation software such as HyperTerminal or XModem with the
following software settings:
9600 baud
•
8 data bits
•
no parity checking
•
1 stop bit
•
no flow control
•
Note that the management interface on a physical Sourcefire device is preconfigured with a default IPv4 address.
However, you can reconfigure the management interface with an IPv6 address as part of the setup process.
However, you can reconfigure the management interface with an IPv6 address as part of the setup process.