Cisco Cisco FirePOWER Appliance 7125 설치 가이드

SPECIFICATIONS, REGULATORY, and SECURITY

Physical and Environmental Parameters

Parameter

3D7010/7020/7030

3D7110/7120

3D7115/7125, AMP7150

Form factor

1U, half-rack width

Dimensions (D x W x H)

Single chassis: 12.49” x 7.89” x 1.66” (31.74 cm x 20.04 cm x 4.21 cm)
2-Chassis Tray: 25.05” x 17.24” x 1.73” (63.62 cm x 43.8 cm x 4.44 cm)

21.6 x 19.0 x 1.73 inches (54.9 x 48.3 x 4.4 cm)

Weight (max installed)

Chassis: 7 pounds (3.17 kg)
Single chassis and power supply in tray: 17.7 pounds (8.03 kg)
Double chassis and power supplies in single tray: 24.7 pounds (11.2 kg)

29.0 pounds (13.2kg)

Copper 1000BASE-T

Gigabit copper ethernet fail-open interfaces in a paired configuration
Cable and distance: Cat5E at 50m

Fiber 1000BASE-SX

Not applicable

Fiber bypass with LC connectors
Cable and distance: SX is multimode

fiber (850nm) at 550m (standard)

Not applicable

Copper 1000BASE-T SFP

Not applicable

Gigabit copper ethernet non-bypass

interfaces in a paired configuration
Cable and distance: Cat5E at 50m

Fiber 1000BASE-SX SFP

Not applicable

Fiber non-bypass with LC connectors
Cable and distance: SX is multimode

fiber (850nm) at 550m (standard)
200m (656 ft) for 62.5μm/125μm fiber

500m (1640 ft) for 50μm/125μm fiber

Fiber 1000BASE-LX SFP

Not applicable

Fiber non-bypass with LC connectors
Cable and distance: LX is single mode
fiber (1310nm) at 10km for 9μm/125μm
fiber (standard)

Power supply

200W AC power supply
Voltage: 100VAC to 240VAC nominal (90VAC to 264VAC maximum)
Current: 2A maximum over the full range
Frequency range: 50/60 Hz nominal (47Hz to 63Hz maximum)

450W dual redundant (1+1) AC power supplies
Voltage: 100VAC to 240VAC nominal (85VAC to 264VAC maximum)
Current: 3A maximum for 90VAC to 132VAC, per supply
1.5A maximum for 187VAC to 264VAC, per supply
Frequency range: 47Hz to 63Hz

Operating temperature

0°C to 40°C (32°F to 104°F)

5°C to 40°C (41°F to 104°F)

Non-operating temperature

-20°C to 70°C (-4°F to 158°F)

Operating humidity

5% to 95%, noncondensing
Operation beyond these limits is not guaranteed and not recommended.

5% to 85%, non-condensing
Operation beyond these limits is not guaranteed and not recommended.

Non-operating humidity

0% to 95%, non-condensing

Store the unit below 95% non-condensing relative humidity. Acclimate

below maximum operating humidity at least 48 hours prior to placing

the unit in service.

5% to 90%, non-condensing with a maximum wet bulb of 28°C (82°F) at

temperatures from 25°C to 35°C (77°F to 95°F)
Store the unit below 95% non-condensing relative humidity. Acclimate below

maximum operating humidity at least 48 hours prior to placing the unit in

service.

Altitude

0 ft (sea level) to 5905 ft (0 to 1800m)

Cooling requirements

682 BTU/hour
You must provide sufficient cooling to maintain the device within its

required operating temperature range. Failure to do this may cause a

malfunction or damage to the device.

900 BTU/hour
You must provide sufficient cooling to maintain the device within its required

operating temperature range. Failure to do this may cause a malfunction or

damage to the device.

Acoustic noise

53 dBA when idle. 62 dBA at full processor load.

64 dBA at full processor load, normal fan operation

Meets GR-63-CORE 4.6 Acoustic Noise

Operating shock

No errors with half a sine wave shock of 5G (with 11 msec. duration)

Complies with Bellecore GR-63-CORE standards

Airflow

20 ft

(0.57m

) per minute

Airflow through the device enters at the front and exits at the rear, with

no side ventilation.

140 ft

(3.9m

) per minute

Airflow through the device enters at the front and exits at the rear with no side

ventilation.

Regulatory Conformance

This Sourcefire device conforms to multiple national and international standards. For a full list of regulatory compliance, see the

Sourcefire 3D System Installation Guide

Security Considerations

Before you install your device, Sourcefire recommends that you consider the following:

Locate your device in a lockable rack within a secure location that prevents access by unauthorized personnel.

•

Allow only trained and qualified personnel to install, replace, administer, or service the device.

•

Always connect the management interface to a secure internal management network that is protected from unauthorized access.

•

Hardware Specifications

7000 SERIES

Quick Start Guide - 7000 Series Devices

2014-5.3-3

Page 8 of 8

9770 Patuxent Woods Drive
Columbia, MD 21046 USA
800.917.4134 | +1.410.423.1901
support@sourcefire.com

WARNING!

This Sourcefire device should be installed and maintained by

qualified personnel only. Keep in mind the following safety
information to avoid system damage or personal injury:
Remove all factory packaging before using the device.

•

Provide adequate ventilation to prevent overheating. Do not

•

cover or block vents, or otherwise enclose the device.
The device must be properly grounded when connecting power

•

to the power outlet.
At all times, keep the chassis area free from dust.

•

Lifting the chassis for rack installation may require two people,

•

as the unit is heavy.
To avoid electrical shock, do not open or remove the chassis

•

covers or metal parts without proper instruction.