Cisco Cisco Aironet 1240 AG Access Point 릴리즈 노트
20
Release Notes for Cisco Aironet Access Points for Cisco IOS Release 12.3(7)JA1
OL-8206-01
Caveats
•
CSCef95410—WLCCP packets received from an access point no longer causes the radio interface
output drop counter to increment.
output drop counter to increment.
•
CSCsa67267—The mbssid command no longer fails on the CLI and the GUI.
•
CSCef11167—The access point now returns an accurate value when you poll
cDot11ActiveWirelessClients through SNMP.
cDot11ActiveWirelessClients through SNMP.
•
CSCeh38024—Access point WPAv2 migration mode now supports Cisco Aironet CB20A client
radios running firmware version 2.0.0.184 configured for optional WPAv2.
radios running firmware version 2.0.0.184 configured for optional WPAv2.
•
CSCsa45650—The 802.11b radio interface in 1200 series access points no longer reports its MAC
address as 000000000000 on both the GUI and through SNMP.
address as 000000000000 on both the GUI and through SNMP.
•
CSCsa68532—The results in the Strength %Out field and the Strength dBm field are no longer
reversed when you run a link test from an access point.
reversed when you run a link test from an access point.
•
CSCsa74148—Existing SSIDs are no longer invalid when you configure VLANs for the first time.
•
CSCsa74153—WPAv2 accounting start/stop records no longer appear in the ACS 3.3 RADIUS
accounting log with the client card MAC address as the username instead of the real username.
accounting log with the client card MAC address as the username instead of the real username.
•
CSCsa75865—The radio interface no longer fails and reloads firmware when multiple bssids are
enabled and the beacon period is configured for the minimum setting, 20 kilomicroseconds.
enabled and the beacon period is configured for the minimum setting, 20 kilomicroseconds.
•
CSCsa76923—The access point no longer sends out deauthentication frames with zero MAC
addresses in the source and BSSID fields during a WLSE controlled scan.
addresses in the source and BSSID fields during a WLSE controlled scan.
•
CSCsa77487—After an access point radio scan controlled by a WLSE running software release
2.11, the transmit power is no longer set to -1 dBm on the RM22A 802.11a radio module in 1200
series access points and the 802.11a radio in 1130AG access points.
2.11, the transmit power is no longer set to -1 dBm on the RM22A 802.11a radio module in 1200
series access points and the 802.11a radio in 1130AG access points.
•
CSCed75294—SCHED-3-STUCKMTMR tracebacks no longer appear in Dot11 aaa process.
•
CSCeg87732—show snmp mib ifmib if index command no longer returns different ifindex values.
•
CSCeh30775—Intel 2100 card no longer drops data when CMIC is enabled.
•
CSCeh46596—show dot11 association command returns correct infrastructure client state.
•
CSCeh50286—The dot11 arp cache frees memory when a client disassociates.
•
CSCeh59709 (duplicate of CSCeh54960)—Short slot time no longer enables after rebooting.
•
CSCeh59723—Shared authentications are now allowed on more than one SSID.
•
CSCeh68031—Broadcast storms no longer cause I/O memory depletion on 350 series access points.
•
CSCeh68511—Radius VLAN assignments now work with WPA/TKIP.
•
CSCeh80318—1200 series access point no longer fails to upgrade the radio firmware.
•
CSCeh88870—Infrastructure SSID can now be set using the GUI for a 1200 series access point in
workgroup bridge mode
workgroup bridge mode
•
CSCei02959—GUI and CLI differences for allowed SSID characters is corrected.
•
CSCei12722—Access point authentication requests are correct when MBSSID is enabled.
•
CSCei18019—Wireless client IP address now learned when Layer 3 Mobility enabled on the access
point and mobility trust enabled on the tunnel.
point and mobility trust enabled on the tunnel.
•
CSCsa53672—Console history buffer now operates correctly when connected via WLSM console
port.
port.
•
CSCsa81364—Access point no longer adds two sets of IP/GRE headers if tunnel IP address not
resolved.
resolved.