Cisco Cisco WAP571 Wireless-AC N Premium Dual Radio Access Point with PoE 관리 매뉴얼
Captive Portal
Instance Configuration
Cisco WAP571/E Administration Guide
161
11
An away timeout value is also configured for each user. See the
page. The away timeout value set on the Local Users page has precedence
over the value configured here, unless the value is set to 0 (the default). A value of
0 indicates to use the instance timeout value.
0 indicates to use the instance timeout value.
•
Session Timeout—Enter the time remaining, in seconds, for the CP session
to be valid. After the time reaches zero, the client is deauthenticated. The
range is from 0 to 1440 minutes. The default value is 0.
to be valid. After the time reaches zero, the client is deauthenticated. The
range is from 0 to 1440 minutes. The default value is 0.
•
Maximum Bandwidth Upstream—Enter the maximum upload speed, in
megabits per second, that a client can transmit traffic when using the captive
portal. This setting limits the bandwidth at which the client can send data into
the network. The range is from 0 to 1300 Mbps. The default value is 0.
megabits per second, that a client can transmit traffic when using the captive
portal. This setting limits the bandwidth at which the client can send data into
the network. The range is from 0 to 1300 Mbps. The default value is 0.
•
Maximum Bandwidth Downstream—Enter the maximum download speed,
in megabits per second, that a client can receive traffic when using the
captive portal. This setting limits the bandwidth at which the client can
receive data from the network. The range is from 0 to 1300 Mbps. The
default value is 0.
in megabits per second, that a client can receive traffic when using the
captive portal. This setting limits the bandwidth at which the client can
receive data from the network. The range is from 0 to 1300 Mbps. The
default value is 0.
•
User Group Name—If the Verification Mode is set to Local or RADIUS,
assigns an existing User Group to the CP instance. All users who belong to
the group are permitted to access the network through this portal.
assigns an existing User Group to the CP instance. All users who belong to
the group are permitted to access the network through this portal.
•
RADIUS IP Network—Choose if the WAP RADIUS client uses the
configured IPv4 or IPv6 RADIUS server addresses.
configured IPv4 or IPv6 RADIUS server addresses.
•
Global RADIUS—If the Verification mode is set to RADIUS, check Enable to
use the default global RADIUS server list to authenticate the clients. (See
use the default global RADIUS server list to authenticate the clients. (See
for information about configuring the global RADIUS
servers.) If you want the CP feature to use a different set of RADIUS servers,
uncheck the box and configure the servers in the fields on this page.
uncheck the box and configure the servers in the fields on this page.
•
RADIUS Accounting—Check Enable to track and measure the resources
that a particular user has consumed, such as system time and amount of data
transmitted and received. If you enable RADIUS accounting, it is enabled for
the primary RADIUS server, all backup servers, and globally or locally
configured servers.
that a particular user has consumed, such as system time and amount of data
transmitted and received. If you enable RADIUS accounting, it is enabled for
the primary RADIUS server, all backup servers, and globally or locally
configured servers.
•
Server IP Address 1 or Server IPv6 Address 1—Enter the IPv4 or IPv6
address for the primary RADIUS server for this VAP. The IPv4 address should
be in a form similar to xxx.xxx.xxx.xxx (192.0.2.10). The IPv6 address should
be in a form similar to xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx
(2001:DB8::CAD5:7D91).
address for the primary RADIUS server for this VAP. The IPv4 address should
be in a form similar to xxx.xxx.xxx.xxx (192.0.2.10). The IPv6 address should
be in a form similar to xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx
(2001:DB8::CAD5:7D91).