JVC GR-D260 사용자 설명서
EN
13
GETTING STARTED
MasterPage: Start_Right
This camcorder’s 2-way power supply system
lets you choose the most appropriate source of
power. Do not use provided power supply units
with other equipment.
lets you choose the most appropriate source of
power. Do not use provided power supply units
with other equipment.
Charging The Battery Pack
1
Set the Power Switch to “OFF”.
2
With the arrow on the battery pack pointing
downward, push the battery pack slightly against
the battery pack mount
the battery pack mount
a.
3
Slide down the battery pack until it locks in
place
b.
4
Connect the AC Adapter to the camcorder.
5
Connect the Power Cord to the AC Adapter.
6
Plug the AC Adapter into an AC outlet. The
POWER/CHARGE lamp on the camcorder
blinks to indicate charging has started.
blinks to indicate charging has started.
7
When the POWER/CHARGE lamp goes out,
charging is finished. Unplug the AC Adapter
from the AC outlet. Disconnect the AC Adapter
from the camcorder.
from the AC outlet. Disconnect the AC Adapter
from the camcorder.
To detach the battery pack
Slide the battery pack upward while pressing
PUSH BATT. to detach it.
PUSH BATT. to detach it.
* Provided
NOTES:
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC
BN-VF707U/VF714U/VF733U battery packs.
Using generic non-JVC batteries can cause
damage to the internal charging circuitry.
with JVC Data Battery. Use the JVC
BN-VF707U/VF714U/VF733U battery packs.
Using generic non-JVC batteries can cause
damage to the internal charging circuitry.
● If the protective cap is attached to the battery
pack, remove it first.
● During charging, the camcorder cannot be
operated.
● Charging is not possible if the wrong type of
battery is used.
● When charging the battery pack for the first time
or after a long storage period, the POWER/
CHARGE lamp may not light. In this case, remove
the battery pack from the camcorder, then try
charging again.
CHARGE lamp may not light. In this case, remove
the battery pack from the camcorder, then try
charging again.
● If the battery operation time remains extremely
short even after having been fully charged, the
battery is worn out and needs to be replaced.
Please purchase a new one.
battery is worn out and needs to be replaced.
Please purchase a new one.
● Since the AC Adapter processes electricity
internally, it becomes warm during use. Be sure to
use it only in well-ventilated areas.
use it only in well-ventilated areas.
● Using the optional AA-VF7 Battery Charger, you
can charge the BN-VF707U/VF714U/VF733U
battery pack without the camcorder.
battery pack without the camcorder.
● After 5 minutes has elapsed in Record-Standby
mode with the cassette inserted, the camcorder
will automatically turn off its power supplied from
the AC adapter. In this case, the battery charge
starts if the battery is attached to the camcorder.
will automatically turn off its power supplied from
the AC adapter. In this case, the battery charge
starts if the battery is attached to the camcorder.
Using The Battery Pack
Perform steps
2 – 3 in “Charging The Battery
Pack”.
Maximum continuous recording time
* Provided
Power
POWER/
CHARGE
M
A
POWER/CHARGE lamp
Battery pack
PUSH BATT.
Open the cover.
Power switch
mark
Arrow
Battery pack mount
To DC connector
To AC outlet
AC Adapter
Power cord
Battery pack
Charging time
BN-VF707U*
Approx. 1 hr. 30 min.
BN-VF714U
Approx. 2 hr. 40 min.
BN-VF733U
Approx. 5 hr. 40 min.
Battery pack
LCD monitor
on
Viewfinder on
BN-VF707U*
1 hr. 5 min.
1 hr. 25 min.
BN-VF714U
2 hr. 20 min.
3 hr.
BN-VF733U
5 hr. 25 min.
7 hr. 5 min.
CONTINUED ON NEXT PAGE
GR-D260PAL_04Start.fm Page 13 Friday, April 1, 2005 11:50 AM