JVC GR-D650US 사용자 설명서
TROUBLESHOOTING
48
EN
MasterPage: Left
➜Push in the memory card a few more times.
● The viewfinder is pulled out and “PRIORITY” is
set to “FINDER”.
➜Push the viewfinder back in or set “PRIORITY” to
“LCD”. (
● The LCD monitor’s brightness setting is too dark.
➜Adjust the brightness of the LCD monitor.
➜If the monitor is tilted upward 180 degrees, open
the monitor fully. (
● A malfunction of some kind has occured. In this
case the camcorder’s functions become
unusable.
unusable.
➜ pg. 49.
● “REMOTE” is set to “OFF”.
➜Set “REMOTE” to “ON”. ( pg. 31, 33)
● The remote control does not point at the remote
sensor.
➜Point at the remote sensor. ( pg. 24)
● The remote control batteries are exhausted.
➜Replace the batteries with fresh ones. ( pg. 24)
Warning Indications
Displays the battery remaining power.
Remaining power level
As the battery power comes close to nil, the
battery remaining power indicator blinks.
When the battery power is exhausted, power
turns off automatically.
battery remaining power indicator blinks.
When the battery power is exhausted, power
turns off automatically.
● Appears if a tape is loaded.
● Blinks when no tape is loaded.
Appears when the erase protection tab is set to
“SAVE” while the Power Switch is set to “REC”
and the VIDEO/MEMORY Switch is set to
“VIDEO”. (
“SAVE” while the Power Switch is set to “REC”
and the VIDEO/MEMORY Switch is set to
“VIDEO”. (
Appears if condensation occurs. When this
indication is displayed, wait more than 1 hour
until condensation disappears.
indication is displayed, wait more than 1 hour
until condensation disappears.
Appears if a tape is not loaded when the
Recording Start/Stop Button or SNAPSHOT
Button is pressed while the Power Switch is set
to “REC” and the VIDEO/MEMORY Switch is set
to “VIDEO”.
Recording Start/Stop Button or SNAPSHOT
Button is pressed while the Power Switch is set
to “REC” and the VIDEO/MEMORY Switch is set
to “VIDEO”.
Appears when the tape ends during recording or
playback.
playback.
●
Appears when the date/time is not set.
(
(
●
The built-in clock battery has run out and the
previously set date/time has been erased.
Consult your nearest JVC dealer for
replacement.
previously set date/time has been erased.
Consult your nearest JVC dealer for
replacement.
Appears for 5 seconds after power is turned on if
the lens cap is attached or when it is dark.
the lens cap is attached or when it is dark.
Appears if Audio Dubbing is attempted on a
blank portion of a tape. (
blank portion of a tape. (
●
Appears if Audio Dubbing is attempted on a
tape recorded in the LP mode. (
tape recorded in the LP mode. (
●
Appears if Audio Dubbing is attempted on a
tape recorded in 16-BIT audio. (
tape recorded in 16-BIT audio. (
●
Appears if A. DUB (
) on the remote control
is pressed when the erase protection tab is set
to “SAVE”. (
to “SAVE”. (
The memory card cannot be removed from
the camcorder.
the camcorder.
Picture does not appear on the LCD monitor.
An error indication (01 – 04 or 06) appears.
The remote control does not work.
CHECK TAPE’S ERASE PROTECTION TAB
Exhausted
High
USE CLEANING CASSETTE
CONDENSATION, OPERATION
PAUSED PLEASE WAIT
TAPE!
TAPE END
SET DATE/TIME!
LENS CAP
A. DUB ERROR!
A. DUB ERROR!
<CANNOT DUB ON A LP RECORDED TAPE>
<CANNOT DUB ON A 16BIT RECORDING>
<CHECK TAPE’S ERASE PROTECTION
TAB>
<CANNOT DUB ON A LP RECORDED TAPE>
<CANNOT DUB ON A 16BIT RECORDING>
<CHECK TAPE’S ERASE PROTECTION
TAB>
GR-D650US.book Page 48 Monday, February 27, 2006 9:38 AM