JVC GR-DZ7 사용자 설명서

MasterPage: Advan_Right

The audio track can be customized only when recorded 
in the 12-BIT and SP modes. (

● Use the provided remote control or an optional remote 

control kit RM-V717KITU. 

Play back the tape to locate the point where editing 

will start, then press PAUSE (9).

While holding A. DUB (D) on the remote control, 

press PAUSE (9). The “9D” and “MIC” indicators 
appear.

Press PLAY (U), then begin “narrating”. Speak into 

the microphone.

● To pause dubbing, press PAUSE (9).

To end Audio Dubbing, press PAUSE (9), then STOP 

(8).

To hear the sound during Audio Dubbing
Connect optional headphones to the headphone 
connector or use the AV connector, and set the 
“NARRATION” to the desired mode;

● “OFF” for the playback sound.

● “ON” for the dubbed sound.

● “MIX” for the playback and dubbed sound.

To hear the dubbed sound during playback
Set “NARRATION” to “ON” or “MIX”. (

墌 pg. 29, 32)

● When editing onto a tape that was recorded at 12-BIT, the 

old and new soundtracks are recorded separately.

● If you dub onto a blank space on the tape, the sound may 

be disrupted. Make sure you only edit recorded areas.

● If feedback or howling occurs during TV playback, move the 

camcorder’s microphone away from the TV, or turn down 
the TV’s volume.

● If you change from 12-BIT to 16-BIT in mid-recording and 

then use the tape for Audio Dubbing, it is not effective from 
the point where 16-BIT recording began.

● During Audio Dubbing, when the tape moves to scenes 

recorded in the LP mode, scenes recorded in 16-BIT audio 
or a blank portion, Audio Dubbing stops.

● Audio dubbing is also possible using an optional 

microphone connected to the MIC connector.

● While an optional microphone is connected, the built-in 

microphone is disabled.

● To perform Audio Dubbing with a video unit connected to 

the camcorder’s S/AV connector, first set “S/AV INPUT” to 
“A/V.IN” or “S.IN” in VIDEO Menu. (

墌 pg. 29, 32)

The “AUX” indication appears instead of “MIC”. 

You can record a new scene into a previously recorded 
tape, replacing a section of the original recording with 
minimal picture distortion at the in and outpoints. The 
original audio remains unchanged.

● Use the provided remote control or an optional remote 

control kit RM-V717KITU.

● Before performing the following steps, make sure that 

“TIME CODE” is set to “ON”. (

● Insert Editing is not possible on a tape recorded in the LP 

mode or on a blank portion of a tape.

Play back the tape, locate the Edit-Out point and 

press PAUSE (9). Confirm the time code at this point. 
(

Press REW (

3

) until the Edit-In point is located, 

then press PAUSE (9).

Press and hold INSERT (I) on the remote control, 

then press PAUSE (9). The “9I” indicator and the Time 
Code (min.:sec.) appear and the camcorder enters 
Insert-Pause mode.

Press START/STOP to begin editing.

● Confirm the insert at the time code you checked in step 1.

● To pause editing, press START/STOP. Press it again to 

resume editing.

To end Insert Editing, press START/STOP, then 

STOP (8).

● Program AE with special effects (墌 pg. 38) can be used to 

spice up the scenes being edited during Insert Editing.

● During Insert Editing, the date and time information 

changes.

● If you perform Insert Editing onto a blank space on the 

tape, the audio and video may be disrupted. Make sure you 
only edit recorded areas.

● During Insert Editing, when the tape moves to scenes 

recorded in the LP mode or a blank portion, Insert Editing 
stops. (

GR-DZ9_DZ7US.book  Page 43  Tuesday, May 18, 2004  10:15 AM