Mitsubishi Electronics dx-tl4709u 사용자 설명서

20

Copy 2 is a backup or archive feature. This item is used to 
copy the data to Copy 2 device by specifying only the start 
point. The point is specifi ed by the date and time or the book-
mark. The copy continues until the end point of the recording 
data reaches or the media to be copied becomes full unless 
the copy is stopped manually (when “FIFO Overwrite” is set 
to “Off”). This function is useful for making backup of the re-
cording data.

 Before executing the copy, make sure that the Copy 2 

device is connected and set in the <Add/Remove HDD 
Device> and <Add/Remove DVD/CD Drive> correctly. 
(System Menu   Memory)

Copy Data to Copy 2 Drive

Set Copy 2 Drive

Range of Copy

User Menu

1.  Set the camera number to be copied.

•  The button function changes between “All Off” 

and “All On” each time you select this button. 
You can switch on and off for all the cameras 
easily by using this button.

•  The picture is not copied when there is no 

recorded picture of the set camera number or 
time.

2.  Select “Other settings” and then set the detailed 

settings.

Main: Sets the area which contains the 

data to be copied. The available setting items are 
“Normal,” “Alarm,” and “LPA.”

To Copy 2: Sets the group to where the data is 
copied. The available setting items are “SerialBus,” 
“DVD/CD,” and “Internal.”

Data: Sets the data area to be copied. The 

available setting items are “Alarm” and “All.”

 Overwrite: Selects whether or not to overwrite the 

existed data.

Eject: Selects whether to eject media (CD/

DVD) automatically when the copy is over.

Overwrite: Selects whether to repeat 

copying from the start point of the media by 
overwriting the existed data, or to stop copying 
when the capacity of the media becomes full 
during copying. This setting is available only when 
the copy destination is HDD.

 “Alarm” appears for “From Main” when “Alarm Recording 

Area” is set to other than “0 %.” (System Menu   Memory 

 Data Management Setting for Main Memory)

 “LPA” appears for “From Main” when “Long Pre-Alarm 

Area” is set to other than “0 %.” (System Menu   Memory 

 Data Management Setting for Main Memory)

 When copying the data to DVD while “Overwrite” is set 

to “On,” the unit clears the existed data of the disc before 
overwriting with new data. Note that clearing the data 
takes about 30 to 40 minutes. You cannot cancel opera-
tion during clearing the data of the DVD.

 When copying the data while “Copy Data” is set to “Alarm,” 

the unit performs copy operation, however, the data is not 
copied if there is no alarm recording data within the speci-
fi ed range of copy. In case of CD/DVD disc, the remaining 
capacity becomes low because only the management 
information is recorded.

 Do not use the disc which has been used on the personal 

computer, failed to be copied, or stopped during copying 
due to the power failure because they may cause mal-
function of the unit.

3. Select 

<Copy Data to Copy 2 Drive> and select 

“Start” 

or 

“Continue” and then select “Set.” Input the start 

time or select the bookmark of copy.

 Start: Sets the start point of copy.
 Continue: Starts copying from the end point of the 

previous copy.
•  To set the start point using the bookmark, 

select “Bookmark” and then select the desired 
bookmark number.

•  To copy from the oldest recording time, select 

“Copy Start Time.”

4. Select 

“Execute.”

•  The copy starts.
•  To stop copy manually, select “Cancel” in the 

screen of <Copy Data to Copy 2 Drive>. The 
data which has been copied before cancelling is 
copied.

 The warning is displayed when the copied range exceeds 

the available capacity of the device to be copied when 
“FIFO Overwrite” is set to “Off” and the copy destination 
is HDD. In this case, set the copy setting again with nar-
rower copy range or use a copy device with larger capac-
ity.

 When the copy is performed during recording, the picture 

of the recording start and end points may not be record-
ed.

 When the recording data of the main device which is be-

ing copied is about to be overwritten or has been over-
written, copy is stopped. Be careful for the copy which 
requires long time such as overwriting copy of DVD.

 The progress bar of copy is not displayed for copy 2.

 The picture data is processed in 2 MB unit. Therefore the 

data is copied in 2 MB unit from the start point of the des-
ignated range when copying.