Manualsbrain.com
ko
English
Deutsch
Español
Français
Italiano
Português
Русский
日本語
中文
매뉴얼
브랜드
Fagor
8025 t cnc
사용자 설명서
Fagor 8025 t cnc 사용자 설명서
다운로드
좋아요
전체 화면
표준
페이지
중
309
바로가기
6.15.4.
Cancellation of tool radius compensation ...................................................................... 59
6.16.
G47. Single block treatment
G48. Cancellation of single block treatment ................................................................... 62
6.17.
G49. Programmable feedrate override ............................................................................. 62
6.18.
G50. Loading of the values in the tool offset table .......................................................... 63
6.19.
G51. Alteration of the I and K values of the engaged tool ............................................. 64
6.20.
G52. Communication with the FAGOR Local Area Network ....................................... 65
6.21.
G53-G59. Zero offsets ..................................................................................................... 67
6.21.1.
G59 As additive zero offset ............................................................................................. 70
6.22.
G65. Independent axis execution ..................................................................................... 70
6.23.
G70/G71. Units of measurement ..................................................................................... 70
6.24.
G72. Scaling factor .......................................................................................................... 71
6.25.
G74. Machine reference search ....................................................................................... 72
6.26.
Probes .............................................................................................................................. 73
6.26.1.
Definition ......................................................................................................................... 73
6.26.2.
Characteristics .................................................................................................................. 73
6.26.3.
Most common applications .............................................................................................. 74
6.26.4.
G75. Probing .................................................................................................................... 75
6.26.5.
G75 N2. Probing canned cycles ...................................................................................... 76
6.27.
Digitizing with the FAGOR 8025/30 TS CNC ................................................................ 89
6.27.1
Digitizing ......................................................................................................................... 89
6.27.2.
Characteristics of digitizing with the FAGOR 8025/30 TS CNC .................................... 89
6.27.3.
G76. Automatic block generation .................................................................................... 91
6.27.4
Preparation of a digitizing operation and later execution at the machine ........................ 93
6.27.5.
Examples of using G76 .................................................................................................... 97
6.28.
G90 G91. Absolute and incremental programming ......................................................... 102
6.29.
G92. Coordinate preset and setting of maximum S at Constant Surface Speed .............. 104
6.30.
G93. Polar origin preset ................................................................................................... 105
6.31.
G94. Feedrate F in mm/minute (inches/minute) .............................................................. 106
6.32.
G95. Feedrate F in mm/revolution (inches/revolution) ................................................... 106
6.33.
G96. S speed in m/min (ft/min) at Constant Surface Speed ............................................ 107
6.34.
G97. S speed in rpm ........................................................................................................ 107
7.
Coordinate programming ................................................................................................. 108
7.1.
Cartesian coordinates ...................................................................................................... 108
7.1.1.
Linear axes ..................................................................................................................... 108
7.1.2.
Rotary axis ....................................................................................................................... 109
7.2
Polar coordinates ............................................................................................................. 111
7.3.
Two angles (A1,A2) ........................................................................................................ 115
7.4.
Angle and one cartesian coordinate ................................................................................. 116
8.
(F) Programming the feedrate .......................................................................................... 118
9.
(S) Spindle speed and spindle orientation ........................................................................ 119
10.
(T) Tool programming ..................................................................................................... 120
11.
(M) Miscellaneous functions ........................................................................................... 123
11.1.
M00. Program stop .......................................................................................................... 123
11.2.
M01. Conditional stop of program .................................................................................. 124
11.3.
M02. End of program ...................................................................................................... 124
11.4.
M30. End of program with return to beginning ............................................................... 124
11.5.
M03. Clockwise start of the spindle ................................................................................ 124
11.6.
M04. Counter-clockwise start of the spindle ................................................................... 124
11.7.
M05. Spindle stop ............................................................................................................ 124
11.8.
M19. Spindle orientation ................................................................................................. 125
Section
Page
이전
다음
1
…
99
100
101
102
103
…
309