Panasonic KXTGF375 작동 가이드
– “Off”: Voice announcement is not
available as alert.
You can configure this setting using either the
base unit or one of the handsets.
base unit or one of the handsets.
Handset / Base unit
1
For CELL 1: MMENUN#6031
For CELL 2: MMENUN#6032
For CELL 2: MMENUN#6032
2
MbN: Select the desired setting. a
MSAVEN
MSAVEN
3
Proceed with the operation for your unit.
Handset: MOFFN
Base unit: MEXITN
Handset: MOFFN
Base unit: MEXITN
Selecting the alert tone
Handset
1
For CELL 1: MMENUN#6041
For CELL 2: MMENUN#6042
For CELL 2: MMENUN#6042
2
MbN: Select the desired setting.
3
MSAVEN a MOFFN
Temporary alert off
You can temporarily disable the alerts by
pressing MAPP ALERTSN.
pressing MAPP ALERTSN.
Base unit
Press MAPP ALERTSN to temporarily disable
alerts.
R
alerts.
R
is displayed.
R To enable alerts again, press MAPP
ALERTSN again.
Using a Bluetooth wireless
headset (optional) for
landline calls
By pairing a Bluetooth headset to the base
unit, you can have a hands-free conversation
wirelessly for landline calls.
Important:
R Your Bluetooth wireless headset must
unit, you can have a hands-free conversation
wirelessly for landline calls.
Important:
R Your Bluetooth wireless headset must
support the HeadSet Profile (HSP)
specification.
specification.
R 1 headset can be paired to the base unit.
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2
cellular lines, or the headset and 1 cellular
line).
cellular lines, or the headset and 1 cellular
line).
R For best performance, we recommend
using a Bluetooth headset within 1 m
(3.3 feet) of the base unit. A headset can
communicate with the base unit within a
range of approximately 10 m (33 feet).
(3.3 feet) of the base unit. A headset can
communicate with the base unit within a
range of approximately 10 m (33 feet).
Pairing a headset to the base unit
Important:
R Make sure that the Bluetooth headset is not
R Make sure that the Bluetooth headset is not
connected to any other Bluetooth device.
1
Your headset:
Set your headset to pairing mode.
R Refer to the headset operating
Set your headset to pairing mode.
R Refer to the headset operating
instructions.
2
Handset:
MMENUN#621
MMENUN#621
3
If your headset PIN is “0000”, go to
step 4.
If your headset PIN is other than
“0000”, press MCLEARN, then enter your
headset PIN.
R Typically, default PIN is “0000”. Refer
step 4.
If your headset PIN is other than
“0000”, press MCLEARN, then enter your
headset PIN.
R Typically, default PIN is “0000”. Refer
to the headset operating instructions.
4
Press MOKN, then wait until a long beep
sounds.
sounds.
5
MOFFN
R When
R When
is displayed on the base
unit, the headset is available for use.
Connecting/disconnecting a headset
If you cannot connect the headset and base
unit using the headset, you can connect using
the handset.
To use your headset with another Bluetooth
device such as a cellular phone, you may
need to disconnect it from the base unit.
Important:
R Make sure that the headset is turned on.
unit using the headset, you can connect using
the handset.
To use your headset with another Bluetooth
device such as a cellular phone, you may
need to disconnect it from the base unit.
Important:
R Make sure that the headset is turned on.
Handset
1
To connect/disconnect:
MMENUN#622
MMENUN#622
For assistance, please visit http://shop.panasonic.com/support
59
Using Bluetooth® Devices
TGF37x_OI(en-en)_0721_ver110.pdf 59
2015/07/22 13:32:27