Panasonic TX-P50U30B 작동 가이드
FA
Q
Q
s
73
Problem
Actions
S
cr
een
Chaotic image, noisy
•
Set [P-NR] in the Picture Menu (to remove noise).
(p. 28)
•
Check nearby electrical products
(fluorescent lamp, DECT phones, mobile phones, microwave, etc.).
(fluorescent lamp, DECT phones, mobile phones, microwave, etc.).
No image can be
displayed
displayed
•
Is [Contrast], [Brightness] or [Colour] in the Picture Menu set to the minimum?
(p. 28)
•
Please also refer to “Neither image nor sound is produced”
(p. 72)
Blurry or distorted image
(no sound or low volume)
(no sound or low volume)
•
Reset channels.
(p. 36)
•
Please also refer to “Neither image nor sound is produced”
(p. 72)
Unusual image is
displayed
displayed
•
Turn the TV Off with Mains power On / Off switch, then turn it On again.
•
If the problem persists, initialise all settings
[Shipping Condition] (p. 47)
S
ound
No sound is produced
•
Is Sound Mute active?
(p. 8)
•
Is the volume set to the minimum?
•
Is Speaker Selection (VIERA Link) set to [TV]?
•
Please also refer to “Neither image nor sound is produced”
(p. 72)
Sound level is low or
sound is distorted
sound is distorted
•
Sound signal reception may be deteriorated.
•
Set [NICAM] (p. 29) in the Sound Menu to [Off ]. (Analogue only)
•
Please also refer to “Neither image nor sound is produced”
(p. 72)
Unusual sound from
the TV
the TV
•
When power is on, whirring sound of cooling fan or drive noise may be heard from
inside the TV (not a sign of faulty operation).
inside the TV (not a sign of faulty operation).
Digital Channel
No programmes shown
on TV Guide
on TV Guide
•
Reset channels.
(p. 36)
•
Check the digital transmission by contacting Digital UK on 08456 50 50 50 or at www.
digitaluk.co.uk
digitaluk.co.uk
•
Check the analogue broadcast (if still available in your area).
•
Consult an aerial engineer to check the alignment of your aerial.
Cannot find a channel
you have previously
watched
you have previously
watched
•
The channel may broadcast for part of the day.
•
Check the channel in the TV Guide.
(p. 18)
•
Channel position numbers may be changed by broadcasters.
•
Reset channels.
(p. 36)
HDMI
Sound is unusual
•
Set the sound setting of the connected equipment to “2ch L.PCM”.
•
Check the [HDMI1 / 2 Input] setting in the Sound Menu.
(p. 30)
•
If digital sound connection has a problem, select analogue sound connection.
(p. 70)
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
equipment are unusual
when the equipment is
connected via HDMI
•
Check the HDMI cable is connected properly.
(p. 66)
•
Turn the TV and equipment Off, then turn them On again.
•
Check an input signal from the equipment.
(p. 71)
•
Check the output resolution of the equipment.
•
Use equipment compliant with EIA/CEA-861/861D.
Netw
ork
Cannot connect to the
network
network
•
Check the LAN cable is connected properly.
(p. 45)
•
Check the connections and settings.
(p. 45, 46)
•
Check the network equipment and network environment.
•
The router may not be set to issue IP address automatically. If the network administrator
prefers to allocate an IP address, set an IP address manually.
prefers to allocate an IP address, set an IP address manually.
(p. 46)
•
The router may be using MAC address filtering (security setting).
Confirm the MAC Address of this TV (p. 45) and set the router to be able to use it.
Confirm the MAC Address of this TV (p. 45) and set the router to be able to use it.
•
If the problem persists, consult your Internet Service Provider or telecommunications
company.
company.