Panasonic TX-P50U30B 작동 가이드
FA
Qs | On scr
een messages
74
Problem
Actions
O
ther
The TV does not switch
On
On
•
Press and hold the standby On / Off switch on the remote control for about 1 second if
Power LED is red.
Power LED is red.
•
Check the mains lead is plugged into the socket.
•
The fuse in the mains plug may have blown. Replace it with one of an identical rating
(p. 4)
The TV goes into
Standby mode
Standby mode
•
Auto power standby function is activated.
(p. 9)
•
The TV enters Standby mode about 30 minutes after analogue broadcast ends.
The remote control
does not work or is
intermittent
does not work or is
intermittent
•
Are the batteries installed correctly?
(p. 6)
•
Has the TV been switched On?
•
The batteries may be running low. Replace them.
•
Point the remote control directly at the front of the TV (within about 7 m and a 30
degree angle of the front of the TV).
degree angle of the front of the TV).
•
Situate the TV so that sunshine or other sources of bright light do not shine on the TV’s
remote control signal receiver.
remote control signal receiver.
Parts of the TV become
hot
hot
•
Temperature rises of parts of the front, top and rear panels will not pose any problems in
terms of performance or quality of the TV.
terms of performance or quality of the TV.
An error message
appears
appears
•
Follow the message’s instructions.
•
If the problem persists, contact your local Panasonic dealer or the authorized Service
Centre.
Centre.
On screen messages
Message
Meaning / Action
All tuning data will be erased
•
[Shipping Condition] will erase all tuning data
(p. 47)
Are you sure ?
•
Confirm correct operation.
Are you sure you want to delete
this timer ?
Press OK to delete timer.
Press RETURN to return.
this timer ?
Press OK to delete timer.
Press RETURN to return.
•
Confirm correct operation.
Bad signal
•
The signal is weak. Check the aerial is plugged in properly. It may be necessary to
have an aerial installer check the signal and aerial alignment.
have an aerial installer check the signal and aerial alignment.
•
Reset channels.
(p. 36)
Child Lock is active!
Press OK to enter PIN.
Press OK to enter PIN.
•
The selected channel is locked in Child Lock (p. 43). You must enter the PIN number
before the channel will be displayed.
before the channel will be displayed.
Feature not available.
•
It is not possible to record from COMPONENT or HDMI. Connect the recorder to the
TV using a fully wired SCART cable for recording from the TV tuner.
TV using a fully wired SCART cable for recording from the TV tuner.
•
Confirm Q-Link or VIERA Link settings
(p. 58 - 61)
Feature not available.
Press OK to view how it works.
Press OK to view how it works.
•
The selected feature on VIERA TOOLS is not available. Press the OK button to view
the demonstration to explain how to use it.
the demonstration to explain how to use it.
Found new software version
∗∗∗
.
Press OK to start update (may
take over 40 mins) or press EXIT
to ignore and you can update
when TV is in standby
take over 40 mins) or press EXIT
to ignore and you can update
when TV is in standby
•
There is a new software available.
Invalid operation - Please check
settings and connections.
settings and connections.
•
Check the Q-Link or VIERA Link connection and setting
(p. 58 - 61)
Invalid system time. Please exit !
•
Cannot get the time information and cannot edit Timer Programming screen.
Check the connection of the RF cable.
Check the connection of the RF cable.
Invalid system time, Timer
Programming will not work.
Please press TV button on
remote control and check time
display on Banner
Programming will not work.
Please press TV button on
remote control and check time
display on Banner
•
Cannot get the time information. If there is no time displayed on the Information
banner, check the connection of the RF cable.
banner, check the connection of the RF cable.
Max. number of timers already
set !
set !
•
The maximum number of timer programming events is 15.