Graupner GmbH & Co. KG MC-20 사용자 설명서
77
Detail program description - Base setup models | Winged models
to the transmitter will fall into Fail-safe mode
during the transmitter-side "binding" period.
during the transmitter-side "binding" period.
"Binding" multiple receivers per model
Multiple receivers per model can be bound if desired,
whereby respective
Multiple receivers per model can be bound if desired,
whereby respective
mc-20
HoTT programs offer the
potential for managing up to four receivers directly
and for dividing up the transmitter's 16 control
channels (max) in any arrangement among these
receivers under menu control. Refer to additional
details further down in this section. First bind the
receivers individually as described below.
However, in subsequent operation only one of
these receivers will establish a telemetry bond to
the transmitter; the one which was activated in the
"TELEMETRY RCV" line of the »Telemetry« menu.
and for dividing up the transmitter's 16 control
channels (max) in any arrangement among these
receivers under menu control. Refer to additional
details further down in this section. First bind the
receivers individually as described below.
However, in subsequent operation only one of
these receivers will establish a telemetry bond to
the transmitter; the one which was activated in the
"TELEMETRY RCV" line of the »Telemetry« menu.
TELEMETRY
SETTING & DATAVIEW
SENSOR SELECT
RF STATUS VIEW
VOICE TRIGGER
SENSOR SELECT
RF STATUS VIEW
VOICE TRIGGER
TELEMETRY RCV
BIND. 1
Any telemetry sensors which may be built into the
model should therefore be connected to this receiver
because the transmitter only receives and evaluates
data from the return channel of the receiver activated on
this line. The second, and all other receivers, operate in
parallel but are fully independent in slave mode.
model should therefore be connected to this receiver
because the transmitter only receives and evaluates
data from the return channel of the receiver activated on
this line. The second, and all other receivers, operate in
parallel but are fully independent in slave mode.
"Binding" transmitter and receiver
Use the
cd selection keys of the left or right touch
pad to move into the "Module" line. The marker frame
will be positioned by default to the column for the next
free binding channel. In the example shown in the
figure below, the marker frame is positioned above the
column label "BD2" because the binding channel in the
column labeled "BD1" is already in use by default for
the receiver which was delivered with the set.
will be positioned by default to the column for the next
free binding channel. In the example shown in the
figure below, the marker frame is positioned above the
column label "BD2" because the binding channel in the
column labeled "BD1" is already in use by default for
the receiver which was delivered with the set.
Another tap on the
SET
key will again deactivate
option selection so a change to another line can be
affected.
affected.
Module
Model name
Stick mode
1
n/a
B A S I C S E T T I N G , M O D E L
Info
n/a
n/a
Module
bind
HoTT
Graubele
1234g/111111
SEL
BD1
BD2
BD3
BD4
The
mc-20
transmitter has a HoTT RF module as
standard equipment. In addition to the built-in module,
there is a connector for an external RF module
behind one of the two front cover fl aps (see page 25)
and a switchover to an external module connected
there can be affected per software. To do this, use the
selection keys of the left or right touch pad to move
the marker frame left to the "Module" selection fi eld
above the "SEL" column label.
there is a connector for an external RF module
behind one of the two front cover fl aps (see page 25)
and a switchover to an external module connected
there can be affected per software. To do this, use the
selection keys of the left or right touch pad to move
the marker frame left to the "Module" selection fi eld
above the "SEL" column label.
HoTT
Graupner HoTT receivers must be "instructed"
to communicate exclusively with a certain model
(memory) in a Graupner HoTT transmitter. This
procedure is known as "binding" and must only be
done once for every new receiver/model-memory-
location combination (and can be repeated anytime).
Graupner HoTT receivers must be "instructed"
to communicate exclusively with a certain model
(memory) in a Graupner HoTT transmitter. This
procedure is known as "binding" and must only be
done once for every new receiver/model-memory-
location combination (and can be repeated anytime).
Important notices:
During the binding procedure be sure the
•
transmitter's antenna is always far enough
away from the receiver's antenna. To be on the
safe side, keep them at least one meter apart.
Otherwise there is a risk of a faulty connection to
the return channel and malfunctions will result.
When binding additional receivers, note that any
away from the receiver's antenna. To be on the
safe side, keep them at least one meter apart.
Otherwise there is a risk of a faulty connection to
the return channel and malfunctions will result.
When binding additional receivers, note that any
•
other –switched on– receivers already bound
Model name
Stick mode
1
n/a
B A S I C S E T T I N G , M O D E L
Info
n/a
n/a
Module
bind
HoTT
Graubele
1234g/111111
SEL
BD1
BD2
BD3
BD4
If not already off, now switch the receiver on. The red
LED on the receiver will blink.
Press and hold the
LED on the receiver will blink.
Press and hold the
SET
button on the receiver while
the LED continues to blink red for about 3 seconds
then, after about another 3 seconds, begins to blink
red/green. The
then, after about another 3 seconds, begins to blink
red/green. The
SET
button on the receiver can now
be released. As long as this LED blinks red/green, the
receiver is in bind mode.
Now, within this 3 second period, start the so-called
"receiver binding" process for the receiver to the
currently active model memory with a brief tap on the
center
receiver is in bind mode.
Now, within this 3 second period, start the so-called
"receiver binding" process for the receiver to the
currently active model memory with a brief tap on the
center
SET
key of the right touch pad. At this time,
the screen's display will blend in a message window
for the duration of the "binding" process.
for the duration of the "binding" process.
Model name
Stick mode
1
n/a
B A S I C S E T T I N G , M O D E L
Info
n/a
n/a
Module
bind
HoTT
Graubele
1234g/111111
SEL
BD1
BD2
BD3
BD4
FINDING...
If the receiver's LED, again blinking red, changes
within about 10 seconds to continuous illumination
in green, the binding process has been successfully
completed. Your model-memory to receiver
combination is now operationally ready. At this time
the screen will now display " bind " (bound) instead of
"n/a" (not attached).
within about 10 seconds to continuous illumination
in green, the binding process has been successfully
completed. Your model-memory to receiver
combination is now operationally ready. At this time
the screen will now display " bind " (bound) instead of
"n/a" (not attached).