Graupner GmbH & Co. KG MC-20 사용자 설명서
79
Detail program description - Base setup models | Winged models
control channels across as many as four receivers.
This redistribution is subsequently referred to as
"mapping" or "channel mapping" (channel correlation).
Select the receiver to be "mapped" with the selection
keys of the left or right touch pad then tap briefl y on
the center
This redistribution is subsequently referred to as
"mapping" or "channel mapping" (channel correlation).
Select the receiver to be "mapped" with the selection
keys of the left or right touch pad then tap briefl y on
the center
SET
key of the right touch pad.
Channel mapping within a receiver
Analogous to the channel correlation function in
the »Telemetry« menu on page 232, described as
"Channel Mapping", it is very simple to use this menu
item to freely assign the transmitter's control channels
present on the receiver's inputs to any specifi c
receiver outputs (servo connections) for the bound
receiver designated by the column labeled BD1.
Analogous to the channel correlation function in
the »Telemetry« menu on page 232, described as
"Channel Mapping", it is very simple to use this menu
item to freely assign the transmitter's control channels
present on the receiver's inputs to any specifi c
receiver outputs (servo connections) for the bound
receiver designated by the column labeled BD1.
RECEIVER CHANNEL MAP BIND1
Rx Input Ch 1
Rx Input Ch 2
Rx Input Ch 3
Rx Input Ch 4
Rx Output Ch 1
Rx Output Ch 2
Rx Output Ch 3
Rx Output Ch 4
After selection of the desired output with the selection
keys of the left or right touch pad, the appropriate
value fi eld will be framed. Briefl y tap on the center
keys of the left or right touch pad, the appropriate
value fi eld will be framed. Briefl y tap on the center
SET
key of the right touch pad. The current setting
will be displayed in inverse video. Now use the
selection keys of the right touch pad to select the
desired input channel's respective transmitter output,
see page 218.
selection keys of the right touch pad to select the
desired input channel's respective transmitter output,
see page 218.
Note:
The number of lines available in the list (outputs)
corresponds to the maximum number of servos which
can be attached to the given receiver.
The number of lines available in the list (outputs)
corresponds to the maximum number of servos which
can be attached to the given receiver.
BUT CAUTION: If, for example, "2AIL" has been
specifi ed in the "Aileron/camber fl aps" line of the
»Model type« menu then the transmitter will have
allocated control function 2 (ailerons) to control
specifi ed in the "Aileron/camber fl aps" line of the
»Model type« menu then the transmitter will have
allocated control function 2 (ailerons) to control
channels 2 & 5 for the left and right ailerons. The
corresponding receiver inputs to be assigned in this
case would be channels 2 & 5, refer to the example
below.
corresponding receiver inputs to be assigned in this
case would be channels 2 & 5, refer to the example
below.
Examples:
You would like to control each aileron of a large
•
model with two or more servos.
Assign each of the appropriate outputs (servo
connections) to one and the same input (control
channel). In this case, depending on left or right
wing, as the respective input to one of the two
default aileron control channels (2 or 5).
You would like to control the rudder of a large
Assign each of the appropriate outputs (servo
connections) to one and the same input (control
channel). In this case, depending on left or right
wing, as the respective input to one of the two
default aileron control channels (2 or 5).
You would like to control the rudder of a large
•
model with two or more servos.
Assign each of the appropriate outputs (servo
connections) to one and the same input (control
channel). In this case, the default rudder channel
(4), see fi gure bottom right.
Assign each of the appropriate outputs (servo
connections) to one and the same input (control
channel). In this case, the default rudder channel
(4), see fi gure bottom right.
Important notice:
The
The
mc-20
HoTT transmitter's »Tx. output swap«
option permits the transmitter's 16 control functions
to be freely swapped in a similar manner or even
permits multiple outputs to be assigned to the same
control function. To keep controls manageable,
however, we strongly recommend using only one of
the options at a time.
to be freely swapped in a similar manner or even
permits multiple outputs to be assigned to the same
control function. To keep controls manageable,
however, we strongly recommend using only one of
the options at a time.
Channel assignment on other receivers
As already mentioned, the "Rcv Ch map" menu
option can be used to freely distribute the
As already mentioned, the "Rcv Ch map" menu
option can be used to freely distribute the
mc-20
HoTT transmitter's 16 control channels across up
to four receivers, whereby the numbering of outputs
(servo connections) as well as the maximum number
of available lines (outputs) will correspond to the
maximum number of servo connections available on
the given receiver.
to four receivers, whereby the numbering of outputs
(servo connections) as well as the maximum number
of available lines (outputs) will correspond to the
maximum number of servo connections available on
the given receiver.
RECEIVER CHANNEL MAP BIND2
Rx Input Ch 16
Rx Input Ch 16
Rx Input Ch 16
Rx Input Ch 16
Rx Output Ch 1
Rx Output Ch 2
Rx Output Ch 3
Rx Output Ch 4
After selection of the desired output with the selection
keys of the left or right touch pad, the respective input
fi eld will be framed. Tap the center
keys of the left or right touch pad, the respective input
fi eld will be framed. Tap the center
SET
key of the
right touch pad. The current setting will be displayed
in inverse video. Now select the desired input
channel with the selection keys of the right touch pad.
For example, suitable to the above rudder example.
in inverse video. Now select the desired input
channel with the selection keys of the right touch pad.
For example, suitable to the above rudder example.
RECEIVER CHANNEL MAP BIND2
Rx Input Ch 4
Rx Input Ch 4
Rx Input Ch 4
Rx Input Ch 4
Rx Output Ch 1
Rx Output Ch 2
Rx Output Ch 3
Rx Output Ch 4
Note:
The number of lines available in the list (outputs)
corresponds to the maximum number of servos which
can be attached to the given receiver.
The number of lines available in the list (outputs)
corresponds to the maximum number of servos which
can be attached to the given receiver.
RF transmit
This menu line provides an option for manually
switching the transmitter's RF transmission on and
off to specifi c models while the transmitter is in
operation. For example, to save power while a model
is being programmed. If this line option was set to
OFF, it will be canceled (i.e. set to ON) the next
time the transmitter is switched on.
If necessary, use the
switching the transmitter's RF transmission on and
off to specifi c models while the transmitter is in
operation. For example, to save power while a model
is being programmed. If this line option was set to
OFF, it will be canceled (i.e. set to ON) the next
time the transmitter is switched on.
If necessary, use the
cd selection keys of the left or
right touch pad to move into the " RF transmit " line