The Watt Stopper Inc. MR2K 사용자 설명서
CLEANING & MAINTENANCE OPERATIONS
Clean only using a cloth dampened with water and a little
mild detergent. Use of solvents or hydrocarbon-based
cleaners may cause permanent damage.
mild detergent. Use of solvents or hydrocarbon-based
cleaners may cause permanent damage.
Replacing Lamps
When a lamp must be replaced, disconnect power.
Power Fail Memory
After a power failure, all wireless devices automatically
return to the state that they were in immediately prior
to loss of power. All configuration and scene control
information is preserved.
return to the state that they were in immediately prior
to loss of power. All configuration and scene control
information is preserved.
TROUBLESHOOTING FOR WIRELESS
During Set House ID, the LED is not flashing on some
wireless Miro devices.
wireless Miro devices.
•
If LED is solid green before initiating house ID binding:
The device already has another house ID. Reset it to the
factory default so that it can be bound to the desired
house ID. Resetting to factory defaults is described in
the “I need to start over” issue.
The device already has another house ID. Reset it to the
factory default so that it can be bound to the desired
house ID. Resetting to factory defaults is described in
the “I need to start over” issue.
•
If LED is solid yellow after initiating house ID binding:
The device may be out of range of the initiating device.
Add a MRR2 Miro Wireless Repeater to boost signal
range.
The device may be out of range of the initiating device.
Add a MRR2 Miro Wireless Repeater to boost signal
range.
I made a configuration mistake. I need to start over.
You can reset any Miro wireless device to factory default
setting by pressing and holding until the LED changes
to solid yellow (approximately 10 seconds). During the
process, the LED fl ashes yellow and when complete,
it changes to solid yellow. The device can then be
reconfi gured, exactly like any new device (see the Set
House ID section).
setting by pressing and holding until the LED changes
to solid yellow (approximately 10 seconds). During the
process, the LED fl ashes yellow and when complete,
it changes to solid yellow. The device can then be
reconfi gured, exactly like any new device (see the Set
House ID section).
The Dimmer does not work and the status LED is
flashing red.
flashing red.
•
at 1Hz (5 times in 5 seconds):
The dimmer has detected an unsuitable load or load
below the minimum rated load for the applied voltage.
The dimmer has detected an unsuitable load or load
below the minimum rated load for the applied voltage.
To clear the fault condition, tap and wait for the LED
to turn green. Disconnect power, check the load, restore
power and try again.
to turn green. Disconnect power, check the load, restore
power and try again.
WARRANTY INFORMATION
Watt Stopper/Legrand warranties its products to be free of
defects in materials and workmanship for a period of five
(5) years. There are no obligations or liabilities on the part
of Watt Stopper/Legrand for consequential damages arising
out of, or in connection with, the use or performance of this
product or other indirect damages with respect to loss of
property, revenue or profit, or cost of removal, installation or
reinstallation.
defects in materials and workmanship for a period of five
(5) years. There are no obligations or liabilities on the part
of Watt Stopper/Legrand for consequential damages arising
out of, or in connection with, the use or performance of this
product or other indirect damages with respect to loss of
property, revenue or profit, or cost of removal, installation or
reinstallation.
2800 De La Cruz Boulevard, Santa Clara, CA 95050
Technical Support: 800-879-8585
www.wattstopper.com
06145r2 10/2006
FCC NOTICE
FCC ID: Q4BMR2K
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Caution: Any changes or modifications to this device not
explicitly approved by Watt Stopper/Legrand could void your
authority to operate this equipment.
explicitly approved by Watt Stopper/Legrand could void your
authority to operate this equipment.